The review article describes the interplay of fundamental research and advanced processes that have made SiC a unique semiconductor material for power electronic devices. Related to the outstanding physical properties of SiC, the preparation of this material is quite challenging. Processing is carried out at elevated temperatures that require special emphasis on the design of the growth machine and the applied construction materials. Growth inside a closed growth chamber demands the usage of advanced sensors and sophisticated computer simulation of the growth process. The application of advanced 2D and 3D in situ x-ray visualization techniques enables the visualization of the growth process. Reduction of the density of structural defects, a prerequisite for the technical application in power electronic devices, based on fundamental research and understanding of the crystallographic as well as the electronic properties of SiC beyond the knowledge base of standard semiconductor materials.

Power electronics belongs to the future key technologies in order to increase system efficiency as well as performance in automotive and energy saving applications. Silicon is the major material for electronic switches since decades. Advanced fabrication processes and sophisticated electronic device designs have optimized the silicon electronic device performance almost to their theoretical limit. Therefore, to increase the system performance, new materials that exhibit physical and chemical properties beyond silicon need to be explored. A number of wide bandgap semiconductors like silicon carbide, gallium nitride, gallium oxide, and diamond exhibit outstanding characteristics that may pave the way to new performance levels. The review will introduce these materials by (i) highlighting their properties, (ii) introducing the challenges in materials growth, and (iii) outlining limits that need innovation steps in materials processing to outperform current technologies.

Silicon carbide (SiC) is emerging rapidly in novel photonic applications thanks to its unique photonic properties facilitated by the advances of nanotechnologies such as nanofabrication and nanofilm transfer. This review paper will start with the introduction of exceptional optical properties of silicon carbide. Then, a key structure, i.e., silicon carbide on insulator stack (SiCOI), is discussed which lays solid fundament for tight light confinement and strong light-SiC interaction in high quality factor and low volume optical cavities. As examples, microring resonator, microdisk and photonic crystal cavities are summarized in terms of quality (Q) factor, volume and polytypes. A main challenge for SiC photonic application is complementary metal-oxide-semiconductor (CMOS) compatibility and low-loss material growth. The state-of-the-art SiC with different polytypes and growth methods are reviewed and a roadmap for the loss reduction is predicted for photonic applications. Combining the fact that SiC possesses many different color centers with the SiCOI platform, SiC is also deemed to be a very competitive platform for future quantum photonic integrated circuit applications. Its perspectives and potential impacts are included at the end of this review paper.

In this review paper, several new approaches about the 3C-SiC growth are been presented. In fact, despite the long research activity on 3C-SiC, no devices with good electrical characteristics have been obtained due to the high defect density and high level of stress. To overcome these problems, two different approaches have been used in the last years. From one side, several compliance substrates have been used to try to reduce both the defects and stress, while from another side, the first bulk growth has been performed to try to improve the quality of this material with respect to the heteroepitaxial one. From all these studies, a new understanding of the material defects has been obtained, as well as regarding all the interactions between defects and several growth parameters. This new knowledge will be the basis to solve the main issue of the 3C-SiC growth and reach the goal to obtain a material with low defects and low stress that would allow for realizing devices with extremely interesting characteristics.

Silicon carbide single crystals have become widely used as substrates for power electronic devices like diodes and electronic switches. Today, 4 inch and 6 inch wafer diameters are commercially available which are processed from vapor grown crystals. The state of the art physical vapor transport method may be called mature. Nevertheless, low defect density and uniform doping are still topics which can be further improved by current research and development of more sophisticated processes and process control. The aim of the paper is to review the physical vapor transport growth method as applied today. Special emphasis will be put on currently less advanced in situ growth monitoring tools based on 2D and 3D X-ray imaging that could be a tool for production monitoring. These techniques allow a precise determination of the crystal and source material evolution. Another topic will be the processing of highly conductive p-type 4 H-SiC which is of particular interest for power electronic switches.

Nitrogen incorporation changes the lattice spacing of SiC and can therefore lead to stress during physical vapor transport (PVT). The impact of the nitrogen-doping concentration during the initial phase of PVT growth of 4H-SiC was investigated using molten potassium hydroxide (KOH) etching, and the doping concentration and stress was detected by Raman spectroscopy. The change in the coefficient of thermal expansion (CTE) caused by the variation of nitrogen doping was implemented into a numerical model to quantitatively determine the stress induced during and after the crystal growth. Furthermore, the influence of mechanical stress related to the seed-mounting method was studied. To achieve this, four 100 mm diameter 4H-SiC crystals were grown with different nitrogen-doping distributions and seed-mounting strategies. It was found that the altered CTE plays a major role in the types and density of defect present in the grown crystal. While the mounting method led to increased stress in the initial seeding phase, the overall stress induced by inhomogeneous nitrogen doping is orders of magnitude higher.