This article describes a system for measuring and compensating for errors resulting from the cutting process in order to improve the accuracy of the workpiece. Measurements were performed by means of an automatic measurement unit. The diameter of the workpiece was measured at two points, and at the same time, the temperature at the end face of the workpiece was measured. These measurements were used in Statistical Process Control (SPC). Based on the measured values, the process stability was checked and an error correction value was determined for the next item. Moreover, the value of the correction was influenced by the assumed value of tool wear, in accordance with the adopted model, and the possibility of achieving the assumed surface quality. The diameter of the workpiece for SPC purposes was measured under industrial conditions using an automatic measurement unit, which indicates that the temperature of the workpiece during the measurement was significantly higher than the reference temperature. The study focuses on the possibility of identifying a workpiece temperature compensation model in measurements of the workpiece diameter for the purpose of introducing an additional change in the correction value. It was found that a model with a constant correction value and a linear model poorly reflect the nature of the changes. On the other hand, the Autoregressive with Extra Input (ARX) model and the Nonlinear Autoregressive with Extra Input (NLARX) model, with a neural network, are able to map the inertia of the system and map the process with greater accuracy. In this way, measurements performed in industrial conditions can more accurately determine the possibility of achieving the assumed tolerance of the finished product. At the same time, the research shows that the temperature compensation model is nonlinear, and that the maximum possible machining accuracy of the workpiece can be achieved thanks to the repeatable measurement and compensation technique.
A study was made of the machinability of NiTi alloy in turning, under conditions resulting in a small cutting layer. The experiment involved cutting with variable feeds ranging from 0.01 to 0.1 mm/rev. The cutting conditions were carefully chosen, considering the rounding radius of the cutting edge. The machined surface was examined and measured in 3D using a confocal microscope and in 2D with a contact profilometer. These measurements were used to estimate hmin, leading to the development of a surface formation model that considers both the lateral material flow due to hmin and the lateral material flow due to altered thermodynamic conditions from the previous blade pass. A method for evaluating the surface and selecting its characteristics was proposed based on analyses derived directly from surface features: PCA (Principal Component Analysis) and EMD (Empirical Mode Decomposition) with the Hilbert transform (Hilbert–Huang transform). PCA analysis facilitated the examination of individual surface component variances, while analysis of the IMF components enabled the assessment of surface component energy combined with instantaneous frequencies.
Manufacturing in modern industrial sectors involves the machining of components where the undeformed chip thickness inevitably decreases to values comparable to the tool edge radius. Under such conditions, the ploughing effect between the workpiece and the tool becomes dominant, followed by the noticeable formation of a stagnation zone. This paper presents research focused on the analysis of the cutting process for small cross-sections of the removed layers, based on cutting force components. This study investigated the machining of two titanium alloy grades—Ti Grade 5 (Ti-6Al-4V) and Ti Grade 2—with the main focus on process stability. A material separation model was analyzed to demonstrate the mechanism of material flow within the cross-section of the machined layer. It was found that the material has a limited ability to flow sideways at the boundary of the chip thickness, thus determining the probable size of the stagnation zone in front of the cutting edge. Orthogonal cutting experiments enabled the determination of the minimum chip thickness coefficient for constant temperature conditions, independent of the tool edge radius, as 0.313. In oblique cutting tests, the sensitivity of thin-layer machining was demonstrated for the determined values of minimum undeformed chip thickness. By applying the 0–1 test for chaos, the measurement time (parameter ) was determined for both titanium alloys to determine the range of observable chaotic behavior. The analyses confirmed that Ti Grade 2 enters chaotic dynamics much more rapidly than Ti Grade 5 and displays local cutting instabilities independent of the uncut chip thickness.
The objective of this paper is to structure the role of the human in metal machining by organising operator participation into three functional roles and analysing their evolution across increasing levels of automation. Using drilling operations as a representative case study, the research integrates the Human-centric Manufacturing Model with the ISA-95 architecture to compare human involvement in classical, automated and autonomous production environments. The results indicate a systematic shift of human contribution from direct physical execution toward supervisory, cognitive and organisational functions. Advances in machine learning, digital twins and multi-sensor monitoring - together with increasing material complexity such as composite stacks and additively manufactured components - transform machining into a data-driven process requiring human validation and interpretation rather than manual intervention. Consequently, boundary physical roles diminish, while cognitive-augmented and analytical-organisational roles become central to planning, monitoring and governance of autonomous systems. The findings show that increasing autonomy does not eliminate the human from manufacturing but redefines the operator as a supervisor, interpreter and orchestrator of cyber-physical production systems, supporting safety, reliability and continuous improvement in Industry 5.0 environments.