Jian Meng

Dr. Jian Meng


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2026 in Eng
Verified
Journal Article
Open access
PDF file
TZTianlong Zhou
Tianlong Zhou
KLKegang Li
Kegang Li
JLJiawen Liu
Jiawen Liu
JMJian Meng
Jian Meng
Mingliang LiMingliang Li
Mingliang Li
DTDong Tian
Dong Tian
Instability in dump slopes frequently induces landslides, a process governed by complex factors. To investigate the impact of gradation composition on dump slope stability, four distinct gradations were designed, and large-scale laboratory triaxial tests were conducted to characterize their strength and deformation behaviors under varying confining pressures. Concurrently, numerical models of dump slopes with these four gradations were established using Particle Flow Code (PFC) to simulate rainfall infiltration processes. Through a comparative analysis of particle contact force chains, pore water pressure evolution, particle displacement under varying rainfall durations, and safety factors under natural and rainfall conditions, the mechanisms governing the influence of gradation composition on slope stability were elucidated from both macroscopic and microscopic perspectives. Results indicate the following: (1) Gradation composition significantly affects the strength and deformation characteristics of dump materials. Sample group 3 (with a fine-to-coarse particle ratio of 4:6) exhibited the highest strength among the four test samples, with peak deviatoric stresses of 610 kPa, 1075 kPa, and 1539 kPa under confining pressures of 200 kPa, 400 kPa, and 600 kPa, respectively. Its corresponding shear strength parameters were a cohesion of 38.45 kPa and an internal friction angle of 32.55°. In contrast, sample group 4 (fine-to-coarse ratio of 6:4) showed the lowest strength, with peak deviatoric stresses of 489 kPa, 840 kPa, and 1290 kPa under the same confining pressures, and shear strength parameters of c = 25.35 kPa and φ = 30.02°. (2) Gradation modulates contact forces and failure modes via a “skeleton-filling” mechanism. (3) Gradation plays a critical role in controlling pore water pressure evolution and the seepage characteristics of the dump slope model. Among the four designed gradations and their corresponding numerical models, Model 3 was characterized by the highest contact forces and the lowest pore water pressure. It exhibited the highest stability under both natural and rainfall conditions, with safety factors of 1.70 and 1.22, respectively. Conversely, Model 4 showed weak particle contact forces and high pore pressure, demonstrating the poorest stability. It yielded safety factors of only 1.25 and 1.02 under natural and rainfall-saturated conditions, indicating that it represents the least favorable gradation composition. These findings provide valuable references for the optimization of dumping processes and stability control in similar engineering projects.

3 August 2026 in Symmetry
Verified
Journal Article
Open access
PDF file
JMJian Meng
Jian Meng
DLDacheng Lu
Dacheng Lu
JLJiawen Liu
Jiawen Liu
HZHan Zhou
Han Zhou
JFJun Fu
Jun Fu
During underground mining, stope stability is affected by excavation-induced stress redistribution and nonlinear degradation of rock mass strength. The conventional Mathews stability graph method employs an empirical stress factor A, which does not explicitly consider the nonlinear relationship between stress conditions and rock mass strength. In this study, the generalized Hoek–Brown criterion was introduced to define the maximum stress factor (MSF), and a modified stress factor A′ was developed by considering tensile and shear failure mechanisms. The proposed method incorporates the nonlinear stress–stability relationship of underground stopes and improves the reliability of stability assessment. A copper mine in southwest China was selected as a case study. The rock mass quality indices and stress parameters of ten representative stopes were obtained through field investigations, stope roof stress measurements, discontinuity surveys, and laboratory tests. The modified stress factor A′ was incorporated into the Mathews stability graph to account for excavation-induced stress redistribution and rock mass strength degradation. Compared with the conventional method, the modified approach generally reduced the stability numbers of the investigated stopes, with an average reduction of approximately 25.6% (excluding D1780-1, where the confinement strengthening effect resulted in a slight increase in stability number). The revised stability classifications show good consistency with the FLAC3D simulation results and field observations, providing supporting evidence for the application of the proposed method to underground stope stability assessment in the studied mine.

13 August 2026 in Geosciences
Verified
Journal Article
Open access
PDF file
JMJian Meng
Jian Meng
JLJiawen Liu
Jiawen Liu
KLKegang Li
Kegang Li
TZTianlong Zhou
Tianlong Zhou
HZHan Zhou
Han Zhou
Determining the shear strength parameters of granular materials in high waste rock dump slopes is essential for reliable slope stability analysis. In this study, dump materials were sampled from six benches (elevations 2800–2950 m) of an open-pit mine dump slope, and in situ density tests, gradation analyses, and large-scale consolidated drained (CD) triaxial tests were performed. Two PFC2D slope models—one with uniform (spatially averaged) parameters and one with elevation-dependent (layered) parameters—were then established to quantify how spatial heterogeneity affects stability predictions. The results show pronounced vertical heterogeneity: density, porosity, gradation, and shear strength parameters vary systematically among benches, reflecting the combined effects of compaction history and particle segregation during dumping. All specimens exhibited strain hardening and continuous shear contraction, and specimens with a denser, better-graded structure showed higher strength and lower compressibility. The layered model yields a higher factor of safety and shallower, bench-scale slip surfaces, whereas the uniform model underestimates stability and misplaces the critical slip zones. These findings demonstrate that elevation-dependent parameter assignment better represents the heterogeneous failure mechanism of high dump slopes and should be preferred over uniform parameterization in stability analyses of similar waste rock dumps.

2 April 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JMJian Meng
Jian Meng
JLJiawen Liu
Jiawen Liu
JFJun Fu
Jun Fu
KYKexin Yin
Kexin Yin
HZHan Zhou
Han Zhou
ACAn Chen
An Chen
The insufficient bearing capacity of the foundation at waste dumps can easily lead to landslides and other geohazards. At present, discrepancies between the calculated bearing capacity of such foundations and actual field performance are a major cause of these accidents. Therefore, further research into methods for accurately estimating the foundation bearing capacity of waste dumps to guide engineering practice is crucial for preventing such incidents. This study employs a combination of theoretical and case analysis to examine the current calculation methods. We discover that the calculated values are smaller than the actual values. Moreover, by taking into account both the upper load of the waste dumps and the bearing capacity of the lower foundation, we analyzed the main problems leading to the underestimation. In response to the aforementioned issues, this study suggests incorporating the Boussinesq equation into the calculation of the upper load to account for the load distribution across various slope forms and the diffusion and superposition of stress at different foundation positions and depths. Simultaneously, the foundation’s bearing capacity is calculated to increase with burial depth, aligning with the stress at different positions. Finally, a new method for calculating the bearing capacity of foundations at waste dumps was developed. The bearing capacities of the waste dump foundation and the weakest point determined using the proposed method are validated through a case study and FLAC3D numerical simulation. This study can provide a reference for calculating the bearing capacity of foundations in similar waste dumps.