WO₃ electrochromic films have emerged as potential candidates for smart windows due to their cost-effectiveness, fast switching speed, and strong chemical stability. However, the inherent contradiction between the high coloring efficiency of amorphous WO₃ and the cycling durability of crystalline WO₃ remains a critical challenge in practical applications. This study proposes an innovative heterostructure engineering strategy, achieving precise control of the amorphous/crystalline bilayer WO₃ heterointerface (148 nm a-WO₃/115 nm c-WO₃) for the first time through phase boundary regulation, using well-controlled magnetron sputtering and post-deposition thermal annealing processes. Multimodal characterization using XRD, XPS, and SEM indicates that the heterointerface optimizes performance through a dynamic charge transfer mechanism and structural synergistic effects: the optimized bilayer structure achieves 76.57% optical modulation (at 630 nm) under −1.0 V and maintains a ΔT retention rate of 45.02% after 600 cycles, significantly outperforming single amorphous (8.34%) and crystalline films (14.34%). XPS analysis reveals a dynamic equilibrium mechanism involving W⁵⁺/Li⁺ at the interface, and the Li⁺ diffusion coefficient (D₀ = 4.29 × 10⁻¹⁰ cm²/s) confirms that the amorphous layer dominates rapid ion transport, while the crystalline matrix enhances structural stability through its ordered crystalline structure. This study offers a new paradigm for balancing the efficiency and longevity of electrochromic devices, with the compatibility of magnetic sputtering promoting the industrialization process of large-area smart windows.

Electrochemical exfoliation is an efficient approach for producing MoS₂ nanosheets, yet the correlation between exfoliation conditions, structural evolution, and nonlinear optical (NLO) properties remains insufficiently understood. In this work, MoS₂ nanosheets were prepared using two representative electrolyte systems, acetonitrile/TPABr and aqueous Na₂SO₄, under controlled voltages. The results reveal distinct exfoliation mechanisms, where ion intercalation dominates in the nonaqueous system, while bubble-assisted processes prevail in the aqueous system. Structural and chemical analyses (Raman, XRD, EDS, and XPS) demonstrate that the nonaqueous system yields MoS₂ with higher crystallinity and lower oxidation degree, whereas the aqueous system shows increased oxidation with the coexistence of Mo⁵⁺ and Mo⁶⁺ species. Correspondingly, enhanced nonlinear absorption and optical limiting performance are observed. A clear mechanism–structure–property relationship is established, highlighting the critical role of electrolyte environment and applied voltage in tailoring NLO responses. This work provides insights into the controlled preparation of MoS₂ nanosheets for photonic and optoelectronic applications.

Electrochromic tungsten oxide (WO₃) films suffer from gradual performance degradation during repeated ion insertion/extraction processes, while the relationship between electrolyte-dependent ion accommodation and structural stability remains insufficiently understood. Herein, magnetron-sputtered WO₃ thin films were systematically investigated in H₂SO₄, LiClO₄, ZnSO₄, and Al₂(SO₄)₃ electrolytes to clarify the coupling relationship among ion accommodation, electronic structure evolution, microstructural retention, and electrochromic durability. Combined electrochemical measurements with UV–visible spectroscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and reflected electron energy loss spectroscopy (REELS) reveal that electrolyte chemistry regulates the balance between electrochemical activation and structural tolerance. Highly mobile H⁺ and strongly interacting Al³⁺ ions promote rapid ion transport and enhanced W⁶⁺ reduction but may induce excessive structural perturbation, defect accumulation, and accelerated degradation during cycling. Zn²⁺ exhibits intermediate behavior, whereas Li⁺ enables balanced ion accommodation through reversible W⁶⁺/W⁵⁺ conversion while preserving the WO₃ framework. Consequently, the LiClO₄ electrolyte achieves superior electrochromic performance with an optical modulation of 80.97% and improved cycling stability. These results demonstrate that durable electrochromic behavior is governed not by maximizing ion transport or reduction degree, but by achieving a reversible ion accommodation regime compatible with the structural tolerance of the host framework. This work provides a microstructure-oriented strategy for designing stable WO₃-based electrochromic devices through electrolyte regulation.

This study investigates the optimization of RF sputtering power for high-performance ITZO TFTs by correlating the film physicochemical properties, oxygen-related defects, and device characteristics. The films were used as the channel layer in thin-film transistors (TFTs). XRD, UV–Vis spectroscopy, and XPS were systematically used to investigate the effects of sputtering power on the film structure, optical properties, chemical composition, and electrical performance of the devices. The results show that X-ray diffraction (XRD) analysis revealed that the ITZO films prepared at different sputtering powers were predominantly amorphous in structure. UV–Vis measurements indicated that the ITZO films maintained a high optical transmittance (>85%), demonstrating their strong potential for application in transparent electronic devices. X-ray photoelectron spectroscopy (XPS) analysis further showed that the sputtering power affected the chemical states of In, Sn, Zn, and O elements, as well as the concentration of oxygen vacancies in the films. Appropriately increasing the sputtering power was found to help regulate the carrier concentration and defect states of the films. When the sputtering power was 70 W, the ITZO TFT exhibited superior electrical performance, with a saturation mobility of 8.46 cm²·V⁻¹·s⁻¹, a threshold voltage of 1.86 V, a subthreshold swing of 0.29 V/decade, and an on/off current ratio of 4.50 × 10⁹.