To address conventional high-pressure cleaners’ inherent issues of excessive size, high noise levels, and poor small-space suitability, this study employs TRIZ theory for systematic analysis and solution development. The core innovation involves replacing traditional pumps with a novel linear motor, leading to a compact and low-noise design. Electromagnetic and fluid dynamics simulations, validated by experiments, confirm that the optimized prototype achieves a maximum thrust of 150 N, an outlet diameter of 4 mm, and an operating water temperature of 40°C for optimal performance. Compared with traditional pump products, the developed cleaning machine exhibits empirically verified significant advantages in noise reduction, jet velocity, and structural compactness, providing substantial strategic support for industrial transition toward high efficiency, environmental sustainability, and intelligent development.
Shark skin grooves, known to reduce hydrodynamic drag, have inspired riblet structures for flow control. This study investigates their application to airfoils, where flow separation at high angles of attack (AOA) compromises aerodynamic stability and wind turbine performance. Numerical simulations were conducted using the SST k–ω model in ANSYS Fluent to analyze riblets placed on the suction surface (SS) of an airfoil. The riblets—oriented perpendicular to the flow—have a fixed height and width of 1 mm, with total lengths varying from 0.1, 0.2, 0.5, and 0.7 of the chord length. The influence of riblet geometry on trailing-edge (TE) vortex shedding and drag reduction under stall conditions is examined in detail. The results indicate that appropriately sized riblets suppress secondary vortex formation and extend the 2S vortex-shedding regime. Conversely, poorly dimensioned riblets can advance Hopf bifurcation in the wake. Analysis of the transient boundary layer structure reveals that the suppression of vortex shedding is primarily due to riblets attenuating fluid pulsation and Reynolds stresses caused by turbulent bursts.
Nonlinear correlations among modal coefficients enable interpretable reduced-order models (ROMs) for microfluidic flows. In this study, flow around a cylinder in a microchannel at Re = 100 is investigated using proper orthogonal decomposition (POD), dynamic mode decomposition (DMD), and POD + DMD. The sparse identification of nonlinear dynamics (SINDy) is employed to identify nonlinear correlations among modal coefficients. The results show that the first POD mode contains 33% of the total kinetic energy, and the first 14 modes capture 99.2% of the energy. A minimal ROM with only two degrees of freedom is constructed, in which the real and imaginary parts of active modal coefficients differ in phase by π/2 and their magnitude equals the vortex-shedding fundamental frequency (1.067 Hz). Among sparse regression algorithms, the FROLS method yields the sparsest representation (sparsity rate 0.05), whereas other methods give sparsity rate > 0.3. Reducing the temporal resolution from 0.01 to 0.1 increases the manifold dynamics coefficient error from 0% to 0.56%. Only the ROMs built from POD + DMD and DMD preserve essential kinematic resolution. The POD-based ROM fails to maintain correct energy levels over long-time integration. Therefore, the nonlinear correlation between POD + DMD modal coefficients is recommended for developing ROMs in microchannel flows when accuracy, interpretability, and stability are considered together.
Bio-inspired riblet technology has progressed in recent years in suppressing near-wall flow separation and reducing drag. However, significant benefits are obtained only when the riblet geometry matches the local flow conditions. Further study is still required before riblets can be reliably applied to low-speed fan blades, whose flow fields are inherently complex. In the present work, large eddy simulation (LES) is used to examine how riblets oriented perpendicular to the flow direction influence the aerodynamic performance and flow characteristics of an airfoil typical of low-speed turbomachinery. Riblets with various groove widths and heights are designed, and the effect of their placement along the airfoil suction surface (SS) is also investigated. The friction coefficient, pressure coefficient, and near-wall velocity distributions of the different configurations are compared. Based on the friction coefficient, the airfoil SS can be divided into three regions: a rapidly decreasing region (RDR) near the leading edge, a stable region (SR) in the middle, and a fluctuating region (FR) at the trailing edge. It is found that riblets of different sizes placed within the RDR can suppress vortex development and improve the near-wall flow. As a result, the RDR exhibits better adaptability to riblet parameters than the SR and FR. Motivated by these findings, riblets were applied to the blades of a backward centrifugal fan, specifically within the blade RDR, with a uniform width and height of 0.5 mm. Fan test results demonstrate that riblets covering 10–20% of the blade camber line increase the fan efficiency by 4.5% and the total pressure by 4.2%, respectively. The aerodynamic performance of the fan under low-flow conditions is markedly improved.