A novel planar architecture is proposed for tunnel field-effect transistors (TFETs). The advantages of this architecture are exhibited, taking the InAs/Si TFET as an example, and the effects of different device parameters are analyzed in detail. Owing to the gate field being parallel to the tunneling interface, the gate control is enhanced, and a better electrical performance is obtained. Moreover, different from a conventional TFET, in which the effective tunneling area and current can hardly be modulated by the gate length, in our proposed device, the effective tunneling area and current can be adjusted depending on the actual requirements of circuit design, which increases the flexibility of TFET-based circuit design. In addition, the device architecture can also be extended to other materials, such as Ge/Si and GaSb/InAs, and thus be used for both n-type and p-type devices. The results show that the complementary digital inverter structure with InAs/Si as the n-type TFET and Ge/Si as the p-type TFET would be helpful for future ultralow power applications. This proposed structure without any complicated fabrication steps shows better compatibility with CMOS technology compared to other TFETs with heterojunction and structural innovations presented in theoretical works.
25 December 2023 in IEEE Transactions on Microwave Theory and Techniques
An efficient and accurate knowledge-guided neural network (KGNN) modeling method for microwave active devices is proposed. The KGNN-based modeling method specifically constructs a hybrid combined objective function (COF) to constrain and guide neural network modeling, greatly improving modeling accuracy and consistency. In particular, the COF consists of the training error term, the prior knowledge term, and the regularization term. The proposed method can be directly used for large-signal modeling. To improve the modeling accuracy, the proposed method is used to model both the bias-and temperature-dependent isothermal nonlinear current and thermal factor, which is introduced to characterize the influence of the self-heating effect. The depletion capacitance and delay time parameters are also modeled with the proposed method. The base–collector and base–emitter charge formulations are obtained by integrating the corresponding depletion capacitances and delay times. An improved small-signal extraction method for III–V heterojunction bipolar transistors (HBTs) is used to obtain the extrinsic parameters. The developed large-signal model (LSM) is implemented in the advanced design system and fully verified by the small-and large-signal measurements. Good agreement is obtained between measured and simulated results.
Conventional optimization algorithms face challenges such as lengthy computation times, premature termination at non-convergent points, and the generation of local optima when addressing multi-objective optimization. A multi-objective optimization method based on the Non-dominated Sorting Genetic Algorithm-II (NSGA-II) is proposed for optimizing Doherty power amplifier circuits. The pre-layout simulation results show that, compared to traditional design methods, the optimized Doherty power amplifier circuit achieves a 6.4% increase in saturation efficiency, a 3.3% increase in 6 dB roll-off efficiency, and a 1 dB increase in saturation output power at 2.63 GHz. This approach enables multi-objective optimization design for more complex PA circuits and enhances the overall circuit performance.
13 October 2023 in IEEE Transactions on Device and Materials Reliability
To predict the aging effect on indium phosphide (InP) heterojunction bipolar transistors (HBTs), an aging small-signal equivalent circuit modeling method is proposed in this paper, with special attention to the degradation of the key small-signal model parameters of the InP HBTs in aging experiments. Based on the analysis of the aging sensitivity of the complete small-signal equivalent circuit parameters, semi-empirical approach is used to model the degradation of the key parameters in bipolar transistors as a function of stress magnitude and stress time. Its validity and accuracy are demonstrated by comparison of the modeled and measured results for InP HBTs before and after degradation.
4 September 2025 in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
As one of the promising materials in the field of optoelectronics and electronic devices, understanding the metal–semiconductor (MS) contact properties between metal and molybdenum disulfide (MoS2) continuous films is crucial for the research and application of MoS2 continuous film materials. In this article, the effect of hexagonal boron nitride (h-BN) thin film as an insertion layer on the MS contact properties between Ni and monolayer MoS2 continuous thin films is analyzed on the basis of experimental data. Thin-film h-BN as a 2-D material can not only form a good van der Waals contact with the MoS2 material, which could shield the scattering of carriers in MoS2 by other material layer to reduce the distribution resistance, but also reduce the metal-induced bandgap state (MIGS) of MS contact which reduces the specific contact resistance (ρc) and optimizes the MS contact between Ni and MoS2. From the experimental results, the ultrathin insulating h-BN can reduce the specific contact resistance by 45.2% and the contact resistance by 74% when inserted between Ni and MoS2. The conclusion is a good guide for realizing good contact between 2-D materials and metals.