A current challenge in realising clean road transport is non-exhaust emissions. Important advances regarding measurement systems, including well-defined characterisation techniques, as well as regulation, will be made in the next few years. In this work, we present the detailed results of particle emission analyses, consisting of aerosol (size distribution, particle number (PN), and mass (PM)) and electron microscopy (EM) measurements, under different load conditions on a test bed for a wheel suspension and brakes. Standard tyres and brakes from serial production were tested with a high-load driving cycle, while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS, and a GRIMM OPS. Furthermore, samples were analysed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with an SMPS, with peaks at 20 and around 400 . The results of an EM analysis of single particles from the electrostatic sampler match the PSD results. The EM analysis also showed ultrafine particles, mainly containing O, Fe, Si, Ba, Mg, and S, and also fractal particles with high-C fractions. Our results suggest, in agreement with the previously published literature, that particulate emissions are related to the brake disc temperature and occur in significant amounts above a threshold temperature.
The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.
Brake wear is a major contributor to non-exhaust particulate emissions, and standardized measurement methods are currently being extended from light-duty (LD) to heavy-duty (HD) vehicles. However, differences in brake geometry and operating conditions may influence particle transport and sampling representativeness in HD brake emission test systems. This study investigates the influence of brake caliper position on particle emissions and mixing uniformity in an HD brake emission test setup. Experiments were conducted using a dynamometer-based system with four sampling probes distributed across the sampling plane. Emissions of particulate mass (PM10, PM2.5) and particle number (solid and total particle number emissions for particles >10 nm) were measured for two caliper orientations (horizontal and vertical). Mixing quality was assessed by comparing probe-specific emission results to the plane-averaged value. The results show that the vertical orientation was associated with 34% higher PM10 and 40% higher PM2.5 emissions on average, a significant increase. Particle number emissions also increased on average, but the differences were small relative to test repeatability. The more pronounced effect on PM suggests that the caliper position mainly influences the transport and losses of larger particles, which contribute more to PM. In contrast, the uniformity of particle concentration across the sampling plane was similar for both configurations, with deviations comparable to those reported for LD systems. These findings should be considered in the interpretation of results obtained with any similar test systems, comparisons between such systems, and literary reviews.
Non-exhaust emissions represent a growing share of traffic-related particulate matter and are increasingly addressed by regulatory frameworks. This study presents a comparison of two brake emission test cycles, the California Brake Dynamometer Cycle (CBDC) and Worldwide Harmonized Light Vehicles Test Procedure Braking Cycle (WLTP-BC), the latter being formally embedded in current regulations. Firstly, we present a detailed comparison of WLTP-BC and CBDC in terms of parameters that are shown to affect or may affect braking control and particle emissions (braking torque, vehicle speed, acceleration, friction work, disc temperature, etc.). Secondly, we present a way to evaluate test system torque control quality, supplementing the friction work-based method present in United Nations Regulation (UNR) No. 179, and quantitatively assess the control quality between the cycles. CBDC was found to be the more challenging cycle to execute. However, the testbench control architecture was found to be sufficient to execute it with high fidelity. Thirdly, we present the emission results obtained from the cycles, both per kilometre driven, as well as per friction work done. We argue that the latter is better for comparing the emission results obtained from cycles with different braking profiles. Driving the CBDC resulted in higher particle mass (PM) emissions but similar particle number (PN) emissions. In light of this dataset, friction work seems to be a better predictor for PN than for PM. While this study encompasses only a single friction pair, and more tests with different brakes would be required to generalize the findings, the results highlight the importance of cycle selection in emission research, both in terms of quantifying the emissions and demands for the test system.