Danijela Radumilo

Danijela Radumilo

Auto-generated profile, based on publicly available information

Danijela Radumilo


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 August 2026 in Eng
Verified
Journal Article
Open access
PDF file
Mario ŠokacMario Šokac
Mario Šokac
TPTatjana M. Puškar
Tatjana M. Puškar
DRDanijela Radumilo
Danijela Radumilo
NPNatasa Puskar
Natasa Puskar
PVPredrag Vučinić
Predrag Vučinić
DVDjordje Vukelic
Djordje Vukelic
Digital-to-physical orthodontic workflows combine intraoral scanning, 3D printing, rescanning and thermoforming, but each step may introduce dimensional deviation affecting final appliance geometry. This pilot methodological study evaluated relative dimensional deviations across selected stages of a biomedical manufacturing workflow for orthodontic appliances. Anonymized intraoral scan datasets from two patients with eugnathic occlusion were used, providing four arch-level datasets. CAD inspection compared IOS data, printed models, powder-coated printed models, and thermoformed appliances, with an analysis of global RMS surface deviation, anterior/posterior regional differences, spray-related surface offset and material-thickness effects. The highest mean global RMS deviation was found for IOS vs. a printed model (0.090 mm), followed by IOS vs. a powder-coated model (0.088 mm), whereas the direct printed model vs. powder-coated model comparison showed a lower mean RMS deviation of 0.039 mm. Regional analysis showed higher RMS deviations posteriorly (0.077 mm) than anteriorly (0.047 mm). Thermoformed appliance adaptation was affected by material thickness, with a mean RMS deviation of 0.207 mm for 1.0 mm material and 0.282 mm for 1.5 mm material. Local incisor analysis estimated the spray-related surface offset at approximately 0.030 mm. The main dimensional discrepancy was associated with printed model fabrication, while posterior regions and thicker thermoformed material showed greater deviation.

6 May 2026 in Symmetry
Verified
Journal Article
Open access
PDF file
DRDanijela Radumilo
Danijela Radumilo
Milan PecanacMilan Pecanac
Milan Pecanac
SRSrdjan Rakic
Srdjan Rakic
DBDragos Buzdugan
Dragos Buzdugan
VSViorel Aurel Serban
Viorel Aurel Serban
SBSebastian Balos
Sebastian Balos
Bulk metallic glasses (BMGs) exhibit high strength and hardness due to their amorphous atomic structure; however, their wider application is often limited by intrinsic brittleness and localized shear deformation. Metallic glass matrix composites (MGMCs) represent an effective approach to overcome these limitations by introducing crystalline phases into the amorphous matrix, thereby improving mechanical stability and deformation behavior. In this study, an Fe-based MGMC was produced by copper mold casting and its micro-structure and mechanical properties were investigated. Microstructural observations revealed a heterogeneous structure consisting of an amorphous matrix with dispersed crystalline phases, which was confirmed by X-ray diffraction showing a broad amorphous halo with superimposed crystalline peaks. The mechanical response was evaluated using Vickers microhardness measurements under different indentation loads, revealing a pronounced indentation size effect (ISE), where hardness decreases with increasing load and stabilizes at higher loads. The load–indentation relationship follows Meyer’s law with the empirical relation P=0.663d1.9245 and an excellent correlation coefficient (R2=0.9996). The Meyer index n<2 confirms normal ISE behavior. The indentation data were further analyzed using proportional specimen resistance (PSR) and modified PSR models, enabling estimation of the load-independent hardness and providing insight into the deformation behavior of the composite material.