In order to modify the surface of light metals and alloys, plasma electrolytic oxidation (PEO) is a useful electrochemical technique. During the oxidation process, by applying a positive high voltage greater than the dielectric breakdown value of the oxide layer, the formation of a ceramic film onto the substrate material is enabled. The resulting surface presents hardness, chemical stability, biocompatibility, and increased corrosion wear resistance. The current study aims to investigate the corrosion resistance and tribological properties of PEO-modified coatings on titanium substrates produced by applying either direct or pulsed current in a silicate-alkaline electrolyte. In this way, a uniform TiO₂ layer is formed, and subsequently, electrophoretic deposition of hydroxyapatite particles (HAP) is performed. The morpho-structural characteristics and chemical composition of the resulting coatings are investigated using scanning electron microscopy combined with energy dispersive spectroscopy analysis and X-ray diffraction. Dry sliding wear testing of the TiO₂ and HAP-modified TiO₂ coatings were carried out using a ball-on-disc configuration, while the corrosion resistance was electrochemically evaluated at 37 °C in a Ringer’s solution. The corrosion rates of the investigated samples decreased significantly, up to two orders of magnitude, when the PEO treatment was applied, while the wear rate was 50% lower compared to the untreated titanium substrate.

In the present study, the microstructure and mechanical properties of Ti-xTa (x = 5%, 15%, and 25% wt. Ta) alloys produced by using an induced furnace by the cold crucible levitation fusion technique were investigated and compared. The microstructure was examined by scanning electron microscopy and X-ray diffraction. The alloys present a microstructure characterized by the α′ lamellar structure in a matrix of the transformed β phase. From the bulk materials, the samples for the tensile tests were prepared and based on the results and the elastic modulus was calculated by deducting the lowest values for the Ti-25Ta alloy. Moreover, a surface alkali treatment functionalization was performed using 10 M NaOH. The microstructure of the new developed films on the surface of the Ti-xTa alloys was investigated by scanning electron microscopy and the chemical analysis revealed the formation of sodium titanate and sodium tantanate along with titanium and tantalum oxides. Using low loads, the Vickers hardness test revealed increased hardness values for the alkali-treated samples. After exposure to simulated body fluid, phosphorus and calcium were identified on the surface of the new developed film, indicating the development of apatite. The corrosion resistance was evaluated by open cell potential measurements in simulated body fluid before and after NaOH treatment. The tests were performed at 22 °C as well as at 40 °C, simulating fever. The results show that the Ta content has a detrimental effect on the investigated alloys’ microstructure, hardness, elastic modulus, and corrosion behavior.

The hardfacing process aims to increase the life span of structural components in the petrochemical, mining, nuclear and automotive industries. During operation, these components are subject to demands of abrasion wear, cavitation erosion and corrosion. Duplex stainless steels are characterized by high mechanical characteristics and corrosion resistance, but poor behavior to abrasive wear and cavitation erosion. The improvement in wear resistance is possible by selecting and depositing a special alloy on the surface using a joining technique that ensures a metallurgical bonding between the layer and the substrate. The experimental investigations carried out in this work demonstrate the ability of the TIG pulsed welding process to produce layers with good functional properties for engineering surfaces. The “Corodur 65” alloy was deposited on a duplex-stainless-steel substrate, X2CrNiMoN22-5-3, using a series of process parameters that allowed for the control of the cooling rate and heat input. The properties of the deposited layers are influenced not only by the chemical composition, but also by the dilution degree value. Since the deposition of layers through the welding operation can be considered as a process with several inputs and outputs, the control of the input parameters in the process aims at finishing the granulation and the structure in the fusion zone as well as limiting the segregation phenomena. The aim of this work is to investigate the microstructural characteristics of the iron-based alloy layer, Corodur 65, deposited via pulsed current TIG welding on duplex X2CrNiMoN22-5-3 stainless-steel substrates.

Cobalt-based alloys, called Stellite, have a microstructure consisting of complex carbides dispersed in a Co-based solid solution matrix. These alloys are resistant to corrosion, erosion through cavitation, abrasive, and sliding wear. To increase the erosion resistance through cavitation, hardfacing of the stainless steel duplex X2CrNiMoN22-5-3 with Stellite 21 alloy was performed using the pulsed tungsten inert gas (TIG) process. The positive effects of the hardfacing process are the low heat input, reduced distortions, controlled volume of the weld, and reduced susceptibility to hot cracking. The effect of dilution is essential for the quality of the deposited layers and, in this sense, the TIG pulsed current welding process was performed to reduce the excess linear energy and implicitly the substrate melting. Iron dilution levels were in the range between 5.9 and 6.1. The higher Fe content in the first layer does not significantly reduce its hardness or wear resistance through erosion cavitation. Compared with the substrate material, the cavity erosion resistance increases 7 to 11 times even in the first layer hardened by the TIG pulsed current welding process.

Duplex stainless steels are materials with high performance under mechanical stress and stress corrosion in chloride ion environments. Despite being used in many new applications such as components for offshore drilling platforms as well as in the chemical and petrochemical industry, the automotive industry, etc., they face issues of wear and hardness that limit current applications and prevent the creation of new use opportunities. To address these shortcomings, it is proposed to develop a hardfacing process by a special welding technique using a universal TIG source adapted for manual welding with a pulsed current, and a manganese austenitic alloy electrode as filler material. The opportunity to deposit layers of manganese austenitic steel through welding creates advantages related to the possibility of achieving high mechanical characteristics of this steel exclusively in the working area of the part, while the substrate material will not undergo significant changes in chemical composition. As a result of the high strain hardening rate, assisted mainly by mechanical twinning, manganese austenitic alloys having a face-centered cubic crystal lattice (f.c.c) and low stacking fault energy (SFE = 20–40 mJ/m²) at room temperature, exhibit high wear resistance and exceptional toughness. Following cold deformation, the hardness of the deposited metal increases to 465 HV5–490 HV5. The microstructural characteristics were investigated through optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray analysis (EDX), X-ray diffraction (XRD), and Vickers hardness measurements (HV). The obtained results highlighted the feasibility of forming hard coatings on duplex stainless steel substrates.

This paper explores the enhancement of cavitation and corrosion resistance in cast stainless steel through laser beam surface remelting. The influence of laser treatment on material properties was assessed by analyzing the microstructure using optical microscopy, electron microscopy, and X-ray diffraction. Cavitation erosion was evaluated in tap water using an ultrasonic vibration setup, following ASTM G32—2016 standards. Results show that local remelting of the surface with a laser beam causes a reduction in material loss and cavitation erosion rate. Potentiodynamic polarization tests revealed a significant improvement in corrosion resistance, indicated by a reduced corrosion current density in the laser-treated surface. The observed improvements in cavitation and corrosion resistance are attributed to microstructural hardening, characterized by grain refinement and a uniform, homogeneous structure with finely dispersed, small precipitate particles.