In-situ alloy formation by Laser Powder Bed Fusion (PBF-LB/M) from mixtures of easily available elemental powders is an appealing approach for developing and qualifying new alloys for laser based additive manufacturing of metals. However, especially when dealing with high-melting elements, like W, Ta, Mo, or Nb, it is difficult to achieve a homogeneous element distribution and a complete fusion of the powder particles. The aim of this work was to understand the effects of the PBF-LB/M process parameters (laser power, scan speed, laser spot diameter) and three different single- and double-exposure strategies on the fusion of high-melting W, Ta, Mo, and Nb particles in a Ti-matrix. For this purpose, 220 samples with 10 vol.% of the high-melting particle fraction were prepared and analyzed by optical light microscopy and automated image processing, as well as by scanning electron microscopy (SEM). The results are discussed in the context of current research on the process dynamics of PBF-LB/M. Based on that process strategies to support a complete fusion of high-melting particles during in-situ alloy formation are derived. It is shown that the number of unmolten particles can be at least decreased by a factor of ten compared to the most unfavorable parameter combination. For the lower melting elements, Nb and Mo, a complete fusion without any remaining particles visible in the microsections was achieved for certain parameter combinations. The results prove the feasibility of in-situ alloy formation with high-melting alloying elements, but they also demonstrate the necessity to adjust the PBF-LB/M process strategy to achieve a complete dissolution of the alloying elements.

Powder Bed Fusion with Laser Beam of Metals (PBF-LB/M) is one of the fastest growing technology branches. More and more metallic alloys are being qualified, but processing of aluminum wrought alloys without cracks and defects is still challenging. It has already been shown that small parts with low residual porosity can be produced. However, suffering from microscopic hot cracks, the fracture behavior has been rather brittle. In this paper different combinations of temperature gradients and solidification rates are used to achieve specific solidification conditions in order to influence the resulting microstructure, as well as internal stresses. By this approach it could be shown that EN AW-2024, an aluminum-copper wrought alloy, is processable via PBF-LB/M fully dense and crack-free with outstanding material properties, exceeding those reported for commonly manufactured EN AW-2024 after T4 heat treatment.

Powder bed-based additive manufacturing has become increasingly important for industrial applications. In the light of this, qualitative considerations such as the geometrical accuracy, the resulting mechanical properties, and the surface quality of additively manufactured parts must be taken into account. Optical measuring techniques such as confocal laser scanning microscopy, fringe projection and focus variation as well as profilometers are evaluated here, to determine the surface quality of powder bed-based manufactured parts. Even though these surface evaluation methods are established commercially, no standardized measuring procedure has yet been established. Within an experimental study the validity and accuracy of surface measurement methods are evaluated below, taking the limitations of each measurement system and the comparability of areal surface textures into account. The examinations are carried out with the powder materials EN-AW2024, Ti-6V-4Al and PA12, which are processed by electron beam melting, and laser beam melting of metals and polymers. Guidance for a consistent and comparable surface evaluation is thereby provided.

Up to now, minimizing segregation of free-flowing, microscale metal powder mixtures driven by different mass density is an open challenge. In this work, effects of particle size variation on homogeneity of Al-Cu mixtures, with a density ratio of 3.3, are examined. Dry coating Al particles with 0.3 wt% fumed silica SiO_x nanoparticles significantly decreases interparticle attraction. This enlarges the range of free-flowing Al particle sizes to < 20 µm. Powder mixture homogeneity is examined optically in vibrated bulk powder and thinly spread layers. From various powder mixtures, solid samples are built layer by layer with the Additive Manufacturing (3D printing) technology Laser Beam Melting in metal powder bed (LBM). Chemical homogeneity of solids is evaluated via energy-dispersive X-ray spectroscopy, backscattered electron microscopy, metallographic analysis and tensile tests. Persistent homogeneity of Al-Cu powder mixtures and LBM solids is found only with particles < 20 µm dry coated with SiO_x nanoparticles. Observed segregation phenomena are explained with a decrease in particle mobility at increasing local concentration and the decreasing effectiveness of mass in smaller particles. The main effects are based on geometry, so they are expected to be transferrable to other nanoparticles, alloying components and powder bed technologies, e.g., binder jetting.

Spatial and temporal knowledge of temperature evolution is crucial in laser beam welding of low-melting materials such as aluminum alloys. Current temperature measurements are restricted to (i) one-dimensional temperature information (e.g., ratio-pyrometers), (ii) a priori knowledge of emissivity (e.g., thermography), and (iii) high-temperature regions (e.g., two-color-thermography). This study presents a ratio-based two-color-thermography system that enables acquiring spatially and temporally resolved temperature information for low-melting temperature ranges (<1200 K). The study demonstrates that temperature can be accurately determined despite variations in signal intensity and emissivity for objects emitting constant thermal radiation. The two-color-thermography system is further transferred into a commercial laser beam welding set-up. Experiments with varying process parameters are conducted, and the ability of the thermal imaging method to measure dynamic temperature behavior is assessed. Image artifacts presumably caused by internal reflections inside the optical beam path limit the direct application of the developed two-color-thermography system during dynamic temperature evolution.

Powder bed fusion with laser beam of metals (PBF-LB/M) is a widely used technology to produce parts with a high freedom in design paired with excellent mechanical properties. The casting alloy AlSi10Mg features a wide process window and a microstructure with excellent mechanical properties which are not obtainable through conventional manufacturing. One possibility for achieving this is by influencing the solidification which then directly affects the local part properties. In this study, the effect of different laser beam profiles with gaussian and top-hat intensity distributions, as well as the influence of varying parameter sets on the microstructure and microhardness within the same specimen, was examined. A test specimen consisting of many small cubes was built with different parameters. It was found that the local properties can be varied in a wide range. Build-height-dependent in-situ aging effects can thereby be exploited for tailoring the local material properties. Thus, an extra degree of freedom is added to the design of additively manufactured parts.