Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)

Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 May 2026 in Ceramics
Verified
Journal Article
Open access
PDF file
SUSaken Uderbayev
Saken Uderbayev
ADAizhan Dilmanova
Aizhan Dilmanova
AKAigerim Khamit
Aigerim Khamit
GZGulnaz Zhakapbayeva
Gulnaz Zhakapbayeva
K(Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
KYKoktem Yerimbetov
Koktem Yerimbetov
This study investigates the development of sustainable ceramic materials using industrial and agricultural waste from the Kyzylorda region of Kazakhstan. The research focuses on the combined use of local clay, ash from the Kyzylorda thermal power plant (TPP), and rice husk ash (RHA). Experimental investigations included the evaluation of chemical composition, linear and volumetric shrinkage, water absorption, bulk density, and compressive strength of ceramic samples fired at 950–1050 °C. Microstructural (SEM) and phase composition (XRD) analyses were performed to explain the observed behavior. The results showed that the optimal composition was 70% clay, 20% TPP ash, and 10% RHA, which demonstrated the highest compressive strength (15.45 MPa), reduced water absorption, and improved densification. The enhanced performance is attributed to partial vitrification and viscous-phase-assisted densification and the formation of crystalline phases such as mullite, cristobalite, and anorthite. The study confirms that the combined use of TPP ash and RHA enables effective recycling of local waste materials and improves the physical and mechanical properties of ceramic products.

Verified
Journal Article
Open access
PDF file
SUSaken Uderbayev
Saken Uderbayev
AAAkbota Arystanbek
Akbota Arystanbek
СНСактаганова Наргуль
Сактаганова Наргуль
GAGuldana Abiyeva
Guldana Abiyeva
K(Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
KYKoktem Yerimbetov
Koktem Yerimbetov
This study evaluates sustainable dune-sand concrete produced using local dune sand, rice husk ash (RHA), and dried oil sludge. The experimental program included a control mixture (C0) and three modified mixtures (M1–M3). RHA was used as a partial replacement for Portland cement at contents of 20, 40, and 60 kg/m3, while dried oil sludge was introduced as a waste-derived additive at 10, 15, and 20 kg/m3, respectively. The total binder content, defined as Portland cement plus RHA, was maintained at 350 kg/m3, while the mixing-water content and water-to-binder ratio were kept constant at 185 kg/m3 and 0.53, respectively. The RHA was heat-treated at 800 °C for 60 min, immediately quenched in water, and subsequently dried at 105 ± 5 °C until a constant mass was achieved. Among the investigated compositions, M2, containing 310 kg/m3 Portland cement, 690 kg/m3 dune sand, 1110 kg/m3 crushed stone, 40 kg/m3 RHA, and 15 kg/m3 dried oil sludge, exhibited the most balanced overall performance. Its compressive strength reached 27.8 MPa at 7 days, 42.5 MPa at 28 days, and 47.7 MPa at 90 days, while its static modulus of elasticity was 32.7 GPa. M2 also showed the lowest water absorption (3.63%), the highest watertightness grade within the investigated series (W10), and the greatest measured freeze–thaw resistance, completing 223 cycles. Optical microscopy and X-ray diffraction observations indicated a visually more continuous matrix and lower relative intensities of several portlandite peaks in the modified concrete. For the replicate-based properties, mixture composition had a statistically significant effect (p < 0.001). Because RHA and dried oil sludge were varied simultaneously, the results represent their combined effect. M2 is therefore identified as the most balanced composition within the present limited test series, rather than as a universal optimum.

7 August 2026 in Construction Materials
Verified
Journal Article
Open access
PDF file
AAAkbota Arystanbek
Akbota Arystanbek
SUSaken Uderbayev
Saken Uderbayev
INIgor Nedoseko
Igor Nedoseko
АБАйжан Байкунирова
Айжан Байкунирова
K(Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
KAKanat T. Alenov
Kanat T. Alenov
This study evaluates a wet-activated multicomponent organomineral modifier for sustainable concrete. The modifier was produced by co-grinding Portland cement and rice husk ash (RHA) in the presence of Sika® ViscoCrete®-20HE and was subsequently combined with polypropylene fibers. Three modified mixtures were tested after 28 days of curing and compared with a control concrete. The modified concretes achieved compressive strengths of 42.2–45.0 MPa, compared with 36.8 MPa for the control. Among the tested formulations, Mix 2, containing 6 wt.% RHA, 4 wt.% polypropylene fibers, and 1.3 wt.% superplasticizer, showed the most favorable overall performance. Its compressive and flexural strengths reached 45.0 and 5.8 MPa, corresponding to observed differences of 22.3% and 26.1%, respectively, relative to the control formulation. Because the complete mixture compositions and w/c ratios differed, these comparisons do not isolate the contribution of any individual constituent. Fracture toughness increased from 1.15 to 2.16 MPa·m1/2, water absorption decreased from 6.8% to 5.1%, and freeze–thaw resistance increased from 138 to 242 cycles. Qualitative SEM and XRD observations showed morphological and phase-related differences between selected control and modified specimens; however, these observations did not establish the causes of the measured performance differences. In addition, because no compositionally identical non-activated RHA reference or direct reactivity test was included, the independent effect of wet activation on RHA reactivity could not be established. The investigated integrated modifier therefore shows potential for improving concrete performance while enabling the beneficial use of RHA.

5 November 2026 in Construction Materials
Verified
Journal Article
Open access
PDF file
SUSaken Uderbayev
Saken Uderbayev
AKAigerim Khamit
Aigerim Khamit
GZGulnaz Zhakapbayeva
Gulnaz Zhakapbayeva
СНСактаганова Наргуль
Сактаганова Наргуль
ABAigul Budikova
Aigul Budikova
KYKoktem Yerimbetov
Koktem Yerimbetov
This study evaluates a sintered lightweight aggregate produced from a 70:30 mass ratio of loess-like loam to hydraulic ash from the Kyzylorda thermal power plant (TPP), with an external 50:50 TPP-ash–ground-rice-husk dusting mixture. Four dusting regimes (C0–C3) were examined at 1000, 1030, 1060, and 1100 °C using 15 test specimens or portions per condition. C0 was the undusted control; the dusting-mixture-to-raw-granule mass ratios for C1, C2, and C3 were 1:2.5, 1:3.5, and 1:4.9, respectively. Dusting regime and firing temperature affected density, strength, water absorption, pore structure, and thermal conductivity. The selected C2 regime, corresponding to a dusting-mixture-to-granule ratio of 1:3.5, produced at 1060 °C an aggregate with a bulk density of 324 ± 18 kg/m3, cylinder crushing strength of 1.42 ± 0.08 MPa, water absorption of 15.8 ± 0.6%, and effective packed-bed thermal conductivity of 0.078 W/(m·K). Scanning electron microscopy (SEM) showed porous and consolidated regions; local energy-dispersive X-ray spectroscopy (EDS) indicated higher Ca, Al, and Fe in the examined shell region than in the examined core region. Lightweight concrete containing the developed aggregate achieved a dry density of 920 ± 5 kg/m3, 28-day compressive strength of 3.87 ± 0.22 MPa, water absorption of 19.4 ± 0.3%, and thermal conductivity of 0.215 ± 0.010 W/(m·K). The results identify 1060 °C and the C2 dusting regime as a preferred compromise among the tested conditions, based on a comparative assessment of density, cylinder crushing strength, water absorption, and thermal conductivity rather than a weighted numerical optimization.

Verified
Journal Article
Open access
PDF file
SZSaken Zhanatuly
Saken Zhanatuly
SUSaken Uderbayev
Saken Uderbayev
K(Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
GZGulnaz Zhakapbayeva
Gulnaz Zhakapbayeva
ГЖГулнур Жакыпова
Гулнур Жакыпова
ASAizhan Sarsenbayeva
Aizhan Sarsenbayeva
This study investigates the development of a composite material based on agricultural plant waste from Kazakhstan, utilizing a multicomponent binder incorporated with rice husk ash. The implementation of low-clinker binders enables the full utilization of ash dumps from the Kyzylorda thermal power plant (TPP) and rice husk residues from local rice-processing enterprises. Physical and chemical analysis of the ash–cement stone revealed a reduction in portlandite content compared to control samples. Phase composition analysis indicated the presence of hydroaluminate C4AH13 and a reduction in calcite, suggesting accelerated crystallization of calcium silicate hydrates. The formation of crystalline phases and intergrowth structures is assumed to contribute to the strengthening of the gel-like matrix. Experimental optimization of the ash–cement binder with rice husk ash yielded compressive strengths ranging from 3.03 to 4.10 MPa at densities of 790–900 kg/m3, depending on the type of organic filler. These results confirm the feasibility of using locally sourced agricultural waste for the production of heat-insulating and structurally stable composite materials.

10 October 2026 in Geotechnics
Verified
Journal Article
Open access
PDF file
SUSaken Uderbayev
Saken Uderbayev
GZGulnaz Zhakapbayeva
Gulnaz Zhakapbayeva
ABAigul Budikova
Aigul Budikova
NSNargul Saktaganova
Nargul Saktaganova
K(Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
Kazakhstan; saken_uderbayev@mail.ru (S.U.); gulnazzhak.@gmail.com (G.Z.); zhapakhova@mail.ru (A.Z.)
NTNurbolat Orazkhanuly Tursynkozha
Nurbolat Orazkhanuly Tursynkozha
Using a single mean collapse strain can misrepresent settlement in spatially variable loess foundations, potentially leading to unsafe hydraulic-structure design and settlement-induced damage. This study examines an archival empirical correction classified by ground and structural conditions. Engineering-geological records from 12 sites informed the factor classification, and monitored settlements of seven irrigation structures were used for validation. The resulting composite factors range from 1.30 to 1.44 across the specified ground and structural classes. For the seven field cases, the corrected predictions achieved a mean absolute percentage error of 12.7%, compared with 35.2% and 32.4% for the two conventional calculation sets. Archival physical-model observations independently supported the proposed load-redistribution mechanism. The correction provides a transparent way to account for ground variability and structural response in preliminary and design-stage settlement assessments, provided that representative collapse-strain data and a defined wetting scenario are available.