Steel (35CND16) has excellent strength with good hardenability and dimensional stability, and it could be widely used in engineering, mining, and tooling. The present study focused on minimizing cutting forces, flank wear, and temperature generation in the machining zone. The machining process factors include cutting speed, feed rate, and depth of cut. DEFORM 3D simulation outputs closely agreed with the experimental results. The predictive model developed by DEFORM 3D can predict the cutting force and temperature before the actual experiment; therefore, the machining cost can be avoided, which would incur due to improper selection of machining factors. Further, the machining factors were optimized based on ANOVA and regression analysis. Flank wear was increased at high level factors of speed and feed; however, flank wear tends to reduce at the middle level of depth of cut. The average percentage error for cutting force and temperature generation between experimental values and simulated values for force and temperature at machining zone was found to be 2.21% and 1.22%, respectively.
12 May 2023 in Journal of Energy Resources Technology
The paper deals with the properties of copper-based composites. Copper is contributing to the field of automobiles and aerospace industries. The tribological properties of copper are not found to be satisfactory, which may be attributed to the support of producing copper matrix composites with extensive investigations into their properties. Coper-based hybrid composites were fabricated by reinforcing titanium dioxide (TiO2) and molybdenum disulphide (MoS2) to enhance the wear and mechanical properties of copper composites. Three specimens were prepared by powder metallurgy process with the designations of Cu+5wt.TiO2, Cu+5wt.TiO2+2wt. MoS2, and Cu+5wt. TiO2+4wt. MoS2. The metallurgical analysis was done on the specimens using X-ray diffraction (XRD) analysis which confirms the presence and distribution of Cu, TiO2, and MoS2 particles in the specimens. The wear rate was studied on the specimens concerning the sliding velocity, load, and MoS2 content. The statistical analysis and Taguchi analysis highlight the influencing parameters on the wear rate of the material. Linear regression equations were developed to predict the wear rate using DoE. Through this analysis, the sliding velocity of 3m/s, a load of 30N, and a 4 addition of MoS2 were identified as the optimum parameters for the minimal wear rate. The wear mechanism was analyzed using scanning electron microscopy techniques to reveal the adhesion, delamination, and oxidation.
1 July 2019 in IOP Conference Series: Materials Science and Engineering
Nowadays polymer matrix composites are widely used in the areas of automotive, medical, aircraft and aerospace industries. Since, chemically surface modified saw dust with jute fiber reinforced composites play vital role in developing lightweight structural materials in many engineering industries. This study focuses on utilizingchemically surface modified saw dust with jute fiberas reinforcement filler loading malic acid treated and un treated (10 %,20% and 30%) and fiber loading (3-layer jute fiber) in epoxy resin. This composite was fabricated using hand lay-up process. The influence of filler volume fraction and fiber weight fraction on the fracture toughness properties of treated / untreated modified saw dust with jute fiber/filler was studied initially. Test results revealed that the composite 20-volume fraction malic acid treated saw dust with 3-layer jute fiber composite has better fracture properties as compared with other specimens.
This study examines the impacts of key abrasive water jet machining (AWJM) parameters on the machinability of AA7175–15 wt.% ZrB2 metal matrix composites produced via a two-step stir casting route. Jet pressure (100–300 MPa), traverse speed (70–130 mm/min), standoff distance (3–5 mm), and abrasive flow rate (250–450 g/min) were systematically varied to evaluate their effects on surface roughness (Ra), kerf taper angle (KA), and material removal rate (MRR). The experimental setup was designed using response surface methodology based on a central composite design (RSM–CCD), enabling both interaction and curvature effects to be assessed. Analysis of variance indicates that jet pressure exerts the strongest influence on MRR, which may be attributed to the increased kinetic energy and penetration capability of abrasive particles at higher pressures. In contrast, traverse speed was found to play a dominant role in controlling surface roughness and kerf geometry. As traverse speed increased, Ra and kerf taper angle tended to rise, likely due to reduced jet–material interaction time and incomplete erosion of the hard ZrB2-reinforced matrix. Abrasive flow rate contributed positively to MRR up to higher levels, although its effect appeared secondary compared to jet pressure. Regression models developed for all machining responses showed strong predictive performance, with coefficients of determination exceeding 0.95 and statistically insignificant lack-of-fit, suggesting adequate representation of the underlying process behaviour within the investigated parameter range. Scanning electron microscopy of the machined surfaces revealed erosion features such as abrasive ploughing, particle pull-out, and striation formation. These surface morphologies are consistent with the observed variations in Ra and kerf characteristics and reflect the combined ductile–brittle erosion response of the composite. Overall, the study identifies optimised AWJM parameter combinations that can improve both surface quality and machining efficiency when processing AA7175–ZrB2 composites.
This study experimentally investigates the thermo-hydraulic performance of plain and oval-shaped mini-channel heat sinks using deionized water and hexagonal boron nitride (hBN) nanofluids at concentrations of 0.05% and 0.10%. The influence of Reynolds number, channel geometry, and nanoparticle concentration on Nusselt number, heat transfer coefficient, pressure drop, friction factor, and pumping power was quantified. Results showed that the oval mini-channel with 0.10% hBN nanofluid produced the highest thermal enhancement, achieving a 220% increase in Nusselt number and a 240% rise in heat transfer coefficient at Reynolds number 900 compared to plain deionized water. Increasing nanoparticle concentration from 0.05%-0.10% further improved the Nusselt number by 35%, indicating strong particle-driven thermal enhancement. Geometry effects alone contributed an additional 20% improvement, demonstrating the significance of flow restructuring via oval cross-sections. Pressure drop penalties remained moderate, increasing by 11.03% for the oval channel with 0.10% hBN and 7.40% for deionized water relative to plain channels. Overall, the combined effects of optimized channel geometry and hBN nanofluid significantly improved convective heat transfer with acceptable hydraulic losses, establishing oval mini-channels as a superior design for compact high-heat-flux thermal management systems.