Jayaseelan Veerasundaram

Dr. Jayaseelan Veerasundaram

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2021 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
JVJayaseelan Veerasundaram
Jayaseelan Veerasundaram
DJD. Jayabalakrishnan
D. Jayabalakrishnan
ARAshok Gandhi R
Ashok Gandhi R
Muthuramalingam ThangarajMuthuramalingam Thangaraj
Muthuramalingam Thangaraj
JXJ. Francis Xavier
J. Francis Xavier
The proposed study deals with the joining of AA6061 T6 alloy using a novel geometric square wave tool path pattern for adequate mixing of materials with increased stirring time and enlargement of the deformation zone. Experiments were conducted based on the process parameters to imply the stirring effect like rotation speed 1200 rpm, weaving rate 100 mm/min; and specific step sizes (1.0, 1.5, and 2.0 mm). Results show that the Percentage of variation for achieving the higher tensile strength of 11.3%, micro vickers hardness of 12.8% with a step size of 1 mm compared to the linear weldment. The SEM morphologies of the weldment clarify the formation of IMCs like spheroidal cementite with the zeolitic structure for resulting in higher hardness value. The EDAX results confirm the formation of intermetallic precipitates like Mg2Si that leads the precipitation hardening and grain boundary strengthening.

1 June 2022 in Materials Testing
Verified
Journal Article
Closed access
JVJayaseelan Veerasundaram
Jayaseelan Veerasundaram
KKKalaichelvan Kani
Kalaichelvan Kani
SMSeeman Murugesan
Seeman Murugesan
RNRamasamy Nallamuthu
Ramasamy Nallamuthu
Manufacturers often employ the extrusion process to form an object with any cross-section. An experiment was carried out to examine the effect of die angle on the quality of the extruded product. The four types of extrusion dies were designed for finding the desirable quality of aluminium composite extruded billet. The five percentages of the Silicon carbide have been chosen as reinforcement with aluminium alloys. Further, the various extrusion dies configurations were considered as 12:8, 12:2, 12:4, and 8:4 for producing the extruded billets. In addition, the die angles that correspond to the required minimum extrusion load were determined. According to the findings, 12:8 extrusion configurations with a 30° die angle produced the desired quality billet and fine grain structure of extruded product with reduced extrusion load. The extruded billet surface quality was analyzed by scanning electron microscopy.

12 October 2021 in Journal of Nanomaterials
Verified
Journal Article
Open access
PDF file
JXJ. Francis Xavier
J. Francis Xavier
BRB. Ravi
B. Ravi
DJD. Jayabalakrishnan
D. Jayabalakrishnan
CEChakaravarthy Ezilarasan
Chakaravarthy Ezilarasan
JVJayaseelan Veerasundaram
Jayaseelan Veerasundaram
GEG. Gebremichael Elias
G. Gebremichael Elias
Aircraft component manufacturing sector is looking for high precision machining in aircraft components. The present work explores the operability of green manufacturing of Nimonic C263 using dry turning. Nimonic C263 is tough to turn owing to its inherent quality like low conductivity and more work hardening. Therefore, in order to improve this machined surface/integrity, the controlling factors were optimized based on desirability approach for minimum of surface roughness and flank wear during turning of this alloy using CBN insert. L27 orthogonal array was chosen to carry out the experiment. The effects of controlling factors, such as cutting speed (), feed rate (), and cut penetration/depth of cut () on the outputs, were also explored. The feed rate was a major impact to affect surface finish and flank wear. The average error percentage between the experimental and RSM models for surface finish was 4.76 percent and 2.79 percent for flank wear.

6 December 2021 in Manufacturing Review
Verified
Journal Article
Open access
PDF file
SKSrinivasan Senthil Kumar
Srinivasan Senthil Kumar
MSMoranahalli Ponnusamy Sudeshkumar
Moranahalli Ponnusamy Sudeshkumar
CEChakaravarthy Ezilarasan
Chakaravarthy Ezilarasan
SPSivaprakasam Palani
Sivaprakasam Palani
JVJayaseelan Veerasundaram
Jayaseelan Veerasundaram
In the current scenario, machinability of the super alloys is of greater importance in an aircraft turbine engine and land-based turbine applications owing to its superior properties. However, the machinability of these alloys is found to be poor owing to its inherent properties. Hence, a predictive model has been developed based on DEFORM 3D to forecast the machining attributes such as cutting force and insert's cutting edge temperature in turning of Nimonic C263 super alloy. The dry turning trials on Nimonic C263 material were carried out based on L27 orthogonal array using CBN insert. Linear regression models were developed to predict the machining attributes. Further, multi response optimization was carried out based on desirability approach for optimizing the machining attributes. The validation test was carried out for optimal parameter values such as cutting speed: 117 m/min, feed rate: 0.055 mm/rev and depth of cut: 0.25 mm. The minimum cutting force of 304N and insert's cutting edge temperature of 468 °C were obtained at optimum level of parameters.The predicted values by FEA and linear regression model were compared with experimental results and found to be closer with minimum percentage error.The minimum percentage error obtained by FEA and linear regression model for the machining attributes (cutting force, temperature) as compared with experimental values were (0.32%, 0.23%) and (2.34%, 1.63%) respectively.

2 August 2022 in Manufacturing Review
Verified
Journal Article
Open access
PDF file
MKMunuswamy Krishna
Munuswamy Krishna
SKSathuvachari Devarajan Kumar
Sathuvachari Devarajan Kumar
CEChakaravarthy Ezilarasan
Chakaravarthy Ezilarasan
PSPerumalsamy Vishnu Sudarsan
Perumalsamy Vishnu Sudarsan
VAViswanathan Anandan
Viswanathan Anandan
JVJayaseelan Veerasundaram
Jayaseelan Veerasundaram
This article presents an integrated multi-criteria decision making using Entropy, MOORA and COPRAS methods for turning Nimonic C263. Experiments were performed under L27 Taguchi orthogonal array. Dry turning was performed and cubic boron nitride (CBN) was used to turn the alloy. The variables speed, feed and depth of cut were chosen as factors. For each experiment, the shear force component was measured during on line. The insert flank wear was measured after every experiment. The main objective of this paper is to identify the suitable trial to ensure minimum force and flank wear simultaneously. Because of the cost reduction and quality improvement, the controlling factors level should be selected appropriately. Hence, the integrated MCDM technique using MOORA, COPRAS and Entropy was chosen to determine the best experiment out of 27 experiments. Alternatives were ranked and the results were evaluated. The best experiment for minimization of force and flank wear is found to be 125 m/min, 0.055 mm/rev and 0.25 mm. The experimental test were observed with lesser deviation and confirmed that proposal found is more suitable to obtain minimum force and flank wear.

10 June 2022 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
AMA. Mathivanan
A. Mathivanan
GSG. Swaminathan
G. Swaminathan
SPSivaprakasam Palani
Sivaprakasam Palani
SRSuthan R
Suthan R
JVJayaseelan Veerasundaram
Jayaseelan Veerasundaram
NMnagaraj m
nagaraj m
Steel (35CND16) has excellent strength with good hardenability and dimensional stability, and it could be widely used in engineering, mining, and tooling. The present study focused on minimizing cutting forces, flank wear, and temperature generation in the machining zone. The machining process factors include cutting speed, feed rate, and depth of cut. DEFORM 3D simulation outputs closely agreed with the experimental results. The predictive model developed by DEFORM 3D can predict the cutting force and temperature before the actual experiment; therefore, the machining cost can be avoided, which would incur due to improper selection of machining factors. Further, the machining factors were optimized based on ANOVA and regression analysis. Flank wear was increased at high level factors of speed and feed; however, flank wear tends to reduce at the middle level of depth of cut. The average percentage error for cutting force and temperature generation between experimental values and simulated values for force and temperature at machining zone was found to be 2.21% and 1.22%, respectively.