To enhance the performance of ultra-high voltage power fittings in severe weather conditions without altering their current structure, the high-strength and toughness aluminum alloys were rationally selected to study the optimization of the die-casting process. This approach aims to improve the overall longevity and function of the power fittings in extreme climates. First of all, the propose of this study is to use the material’s strength–toughness product (STP) concept to evaluate the material stability of the power fitting impact resistance and fatigue toughness in order to determine the appropriate material selection. Secondly, the location of the mold’s sprue and gate was optimized through finite element simulation to prevent gas volume and flow defects during the casting process. This improves the material’s toughness and anti-fatigue failure characteristics of the product. Then, vacuum equipment and a vacuum valve auxiliary system were added based on the existing die-casting machine, and the mold structure was optimized to enable the vacuum die-casting process. Finally, a water-based boron nitride environmentally friendly mold release agent was used to solve demolding difficulties with an A356 aluminum alloy and improve mold lubrication and surface quality. The production of quad-bundled spacers using A356 and vacuum die casting has resulted in parts with a tensile strength of at least 250 MPa and an elongation of no less than 7%. This improvement has laid a foundation for enhancing the operational reliability of existing overhead transmission line fittings.
Hot stamping for high strength steel is an effective method for lightweight of vehicles. Hot stamping parts provide better structural strength while reducing weight, so as to improve safety performance of cars. But due to dramatic temperature changes for high-strength steel sheets and molds in hot stamping process, the final performance of parts is determined by a variety of complex factors. The dwell time is closely related to the part performance. If dwell time is too short, parts performance will decrease significantly. But reducing the dwell time can effectively shorten the production cycle of hot stamping. In the actual production, the dwell time is always longer in order to ensure the part performance. It is found that for a given part, there is a Critical Dwell Time (CDT); if the dwell time is greater than CDT, the performance of the part reaches the expected performance; if the dwell time is slightly smaller than CDT, the performance of the part decreases slightly. This paper presents an online optimization method of hot stamping process based on part performance. This method uses online non-destructive sensor, which is a Magnetic Barkhausen Noise sensor, to monitor the performance of hot stamping parts, and adjust the dwell time in smaller steps according to the performance of parts. When the performance of the part fluctuates around the expected performance, CDT will be determined. The part performance is monitored continuously, if part performance is lower than expected, the dwell time is increased. By using this method within a control simulation, the performance of the parts keeps as expected, the threshold of the dwell time for the specific part and its performance is obtained, and the forming cycle of the parts (including deformation process and dwelling process) is shortened by about 8~21%, compared with the original one, and the production efficiency of forming equipment in the hot stamping production line will be increased obviously.
In [Wuhan]. These articles have been peer reviewed by the members of the [Scientific Committee] and approved by the Editor-in-Chief, who affirms that this document is a truthful description of the conference's review process.
This paper describes the hot stamping of laser spliced plates based on multi-component integration and the digital transformation of the shop floor. As the global automotive industry faces energy and environmental challenges, automotive lightweighting has become an industry trend, in which high-strength steel replaces traditional materials to achieve lightweighting. Hot stamping technology combines material heat treatment and molding processing to improve the performance of automotive structural components, especially in terms of automotive safety. The concept of multi-component integration in the field of lightweight design and manufacturing as well as the development and application of laser welded panels were also elaborated. The laser ablation welding technology and its application for aluminum-silicon coated plates, the digital process and equipment in the hot stamping shop for high strength steel, and the digital transformation of hot stamping production are discussed and analyzed in depth, and the transformation roadmap of the digital hot stamping shop is put forward, which looks forward to the prospect of digital technology in hot stamping production.
All of the articles in this proceedings volume have been presented at the [The 7th International Conference on Advanced High Strength Steel and Press Hardening] during [August 21-23, 2024] in [Wuhan]. These articles have been peer reviewed by the members of the [Scientific Committee] and approved by the Editor-in-Chief, who affirms that this document is a truthful description of the conference’s review process.