Anhua Xu

Anhua Xu


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 May 2026 in Polymers
Verified
Journal Article
Open access
PDF file
AXAnhua Xu
Anhua Xu
LWLaifa Wang
Laifa Wang
Suining ZhengSuining Zheng
Suining Zheng
JTJia Hui Ting
Jia Hui Ting
XWXinyan Wang
Xinyan Wang
HCHuaxin Chen
Huaxin Chen
Styrene butadiene rubber (SBR) is a commonly used polymer modifier that can improve the mechanical properties and durability of cement mortar. However, the effects of different emulsifier types on cement hydration behavior and structural evolution still need to be systematically studied. To clarify the differences among anionic, cationic, and nonionic SBR emulsions on mortar performance, three types of SBR emulsion were selected in this study. Setting time, chemically bound water, mechanical properties, chloride ion diffusion, freeze–thaw cycles, and microstructure were tested to evaluate the effects of different types and dosages on cement mortar. The results show that all three types of SBR emulsion prolong the setting time of cement paste and reduce the early hydration degree. The cationic SBR emulsion shows a more obvious effect. At 28 d, the compressive strength of mortar with 10% cationic SBR emulsion increases from 38.5 MPa to 41.2 MPa, and the flexural strength also increases. In terms of impermeability, the chloride ion diffusion coefficient decreases from 7.47 × 10−12 m2/s to 5.12 × 10−12 m2/s after adding 10% cationic SBR emulsion. After 100 freeze–thaw cycles, the compressive strength loss of ordinary mortar is 16%, while it decreases to 7.2% with 15% cationic SBR emulsion, and the mass loss is also reduced. Microstructural analysis shows that the modified mortar has a denser internal structure, improved interfacial continuity, and reduced crack development after freeze–thaw cycles.

14 January 2026 in Journal of Measurements in Engineering
Verified
Journal Article
Open access
PDF file
Qingsong DuQingsong Du
Qingsong Du
AXAnhua Xu
Anhua Xu
FWFei Wang
Fei Wang
HLHuimin Luo
Huimin Luo
SQShunshun Qi
Shunshun Qi
Permafrost in the Qinghai-Tibet Plateau is highly susceptible due to thawing and degradation under the climate warming and extreme warming events, which can trigger surface subsidence and uplift phenomena. This study investigates the vertical surface deformation along the Qinghai-Tibet Engineering Corridor (QTEC) based on the dataset derived from interferometric synthetic aperture radar (InSAR) processing of the ascending and descending Sentinel-1 datasets. Using the geographical detector method, 24 potential factors influencing deformation was selected, including climatic, topographic, soil, hydrological, vegetation index, and cryospheric indicators to explore the driving mechanisms according to the q-value of factor detection processing. Results indicate that climatic factors (mean annual temperature and precipitation) and permafrost-related parameters (surface frost number, freezing index, thawing index) are the primary drivers of vertical deformation, with the q-value greater than 0.095. Topographic parameters (latitude, elevation, topographic relief, slope, longitude) also significantly influence deformation with the q -value between 0.054 and 0.086, followed by the east-west deformation rate and soil organic matter content with the q -value at 0.052, while other factors with the q-value less than 0.05. This study elucidates the intrinsic mechanisms driving surface subsidence and uplift along the QTEC, providing a theoretical foundation for the construction of future infrastructure projects and the maintenance of existing engineering facilities in permafrost regions.

28 July 2026 in Polymers
Verified
Journal Article
Open access
PDF file
Suining ZhengSuining Zheng
Suining Zheng
JXJiming Xiao
Jiming Xiao
HCHuaxin Chen
Huaxin Chen
AXAnhua Xu
Anhua Xu
RWRuiyang Wang
Ruiyang Wang
FLFulu Li
Fulu Li
Ethylene–vinyl acetate (EVA) as a redispersible polymer can improve the workability, mechanical properties, and interfacial bonding of repair mortar, but the regulatory effect of different EVA dosages on underwater performance remains unclear. This study investigates EVA–polyacrylamide (PAM) composite-modified repair mortar and systematically evaluates the influence of varying EVA content on mortar performance. Multi-scale methods including setting time measurement, flowability test, flexural and compressive strength tests, underwater flexural bonding strength, water-to-air strength ratio, cement loss rate, porosity, and scanning electron microscopy (SEM) characterization were employed. The results indicate that mortar with 8% EVA exhibits the optimal overall performance. The initial setting time of the cement paste increased from 35 to 47 min, and the final setting time from 55 to 72 min, improving workability. In terms of mechanical properties, the 28-day flexural strength increased from 7.5 to 9.2 MPa, and the compressive strength from 44.4 to 50.6 MPa. Regarding underwater performance, the 28-day underwater flexural bonding strength rose from 5.1 to 6.5 MPa; the water-to-air strength ratio increased from 79.1% to 95.2%, and cement loss rate decreased from 3.18% to 0.32%; pH changes were maintained within a moderate range. Microstructural analysis shows that the total porosity at 28 d decreased from 16.8% to 13.5% for mortar containing 8% EVA, and SEM observations revealed that hydration products uniformly filled pores forming a dense network, consistent with the trends of mechanical and interfacial bonding performance enhancement.

10 September 2026 in Journal of Measurements in Engineering
Verified
Journal Article
Open access
PDF file
Qingsong DuQingsong Du
Qingsong Du
AXAnhua Xu
Anhua Xu
GLGuoyu Li
Guoyu Li
FWFei Wang
Fei Wang
HLHuimin Luo
Huimin Luo
SQShunshun Qi
Shunshun Qi
Warming and wetting on the Qinghai-Tibet Plateau (QTP), together with increasing engineering disturbance, have accelerated permafrost degradation along the Qinghai-Tibet Engineering Corridor (QTEC), inducing surface deformation that threatens infrastructure stability and environmental safety. Interferometric synthetic aperture radar (InSAR) has become an effective tool for large-scale deformation monitoring; however, conventional single-orbit ascending or descending observations measure only one-dimensional line-of-sight (LOS) displacement. Because LOS deformation represents a projection of actual ground motion, it cannot always be directly interpreted as vertical uplift or subsidence, especially where horizontal displacement is significant. In this study, ascending and descending Sentinel-1 InSAR observations from 25 February 2017 to 31 March 2022 were integrated to decompose two-dimensional deformation components, namely east-west and vertical displacement, in the permafrost zone of the QTEC. Based on the decomposed results, surface-deformation types were discriminated, and the interpretation applicability of conventional single-orbit LOS observations was quantitatively evaluated using vertical deformation as a reference. The results show that single-orbit LOS deformation can reasonably represent vertical deformation in 52.84 % of the study area, whereas the remaining 47.16 % is dominated by horizontal displacement and is therefore unsuitable for direct interpretation as uplift or subsidence. These findings highlight the necessity of distinguishing deformation types before interpreting LOS deformation and provide practical guidance for improving the reliability of InSAR-based deformation monitoring and engineering-risk assessment in permafrost corridors.

20 August 2026 in Polymers
Verified
Journal Article
Open access
PDF file
ZWZhaoyang Wang
Zhaoyang Wang
BGBOWEN GUAN
BOWEN GUAN
XWXuetao Wang
Xuetao Wang
AXAnhua Xu
Anhua Xu
XZXin Zheng
Xin Zheng
YZYue Zhang
Yue Zhang
To mitigate high-temperature VOC emissions and reduce construction temperatures in recycled asphalt, a USP warm mix additive was introduced into waste soybean oil (WSO) recycled asphalt. This study systematically investigates the effects of USP content (1%, 3%, 5%, and 7%) and construction temperature (140 °C and 160 °C) on VOCs emission characteristics, inhibition mechanisms, and rheological performance. The results show that USP reduces total VOC emissions, with the key inhibition effect achieved at 5% USP. At 160 °C, the VOCs inhibition rate reached 39.5% at 5% USP, while at 140 °C it increased to 80.8%; the findings suggest that lower temperatures enhance the inhibitory effect. The results show USP cuts emissions via physical mechanisms. However, the significant FTIR and DSC analyses suggest that VOC reduction appears to be primarily governed by physical mechanisms, including phase-change cooling, physical encapsulation, and migration retardation, without altering the chemical structure of asphalt. Moreover, the important rheological results indicate that although USP slightly decreases the high-temperature complex modulus and rutting factor, the evidence demonstrates that it improves the percent recovery (R0.1 from 53% to 66%; R3.2 from 21% to 40%) and low-temperature crack resistance through decreased stiffness S and increased m-value. In light of these significant findings, the study demonstrates that USP exhibits a multi-performance balance, appearing to reduce VOC emissions and improve workability while moderately weakening high-temperature deformation resistance. Notwithstanding the reduced high-temperature resistance, the key evidence could demonstrate that USP enhances elastic recovery and low-temperature performance in the results. The optimal USP content appears to be 5%, providing the critical compromise between emission reduction and pavement performance for WSO recycled asphalt.

5 August 2026 in Materials
Verified
Journal Article
Open access
PDF file
AXAnhua Xu
Anhua Xu
JXJiming Xiao
Jiming Xiao
DYDuan Yuchang
Duan Yuchang
HCHuaxin Chen
Huaxin Chen
JYJincheng Yu
Jincheng Yu
Dongliang KuangDongliang Kuang
Dongliang Kuang
Numerous studies have investigated the application of iron tailings as raw materials for cement concrete, while rare efforts have been devoted to developing epoxy pavement repair mortars where graded IT function simultaneously as fine aggregate and filler. This study prepared epoxy resin mortar for rapid repair of cement concrete pavement using graded iron tailings (IT) as fine aggregate and filler. All mixtures employed IT as fine aggregate, where the mass proportion of IT filler relative to the total IT mixture varied from 0% to 40%. The effects of IT filler content on workability, curing temperature, mechanical properties, volume stability, and bond strength were investigated, accompanied by microstructural analysis. Experimental results reveal that the incorporation of IT filler ameliorates the fresh workability and shortens the setting time of epoxy mortar, whereas the compressive strength, flexural strength and interfacial bond strength exhibit an initial ascending followed by a descending trend with the increasing IT filler fraction. The optimal IT filler content is determined to be 20%. For fresh-state performance, the modified mortar delivers a flowability of 176.8 mm (+29.7% relative to EM-0) and a setting time of 127 min. In terms of hardened mechanical and bonding properties, the 28-day compressive strength, 28-day flexural strength and 7-day flexural bond strength reach 113.2 MPa (+17.2%), 42.5 MPa (+34.0%) and 9.1 MPa (+75.0%), respectively, in comparison with the reference specimen EM-0. Microscopic characterizations deliver indirect evidence that appropriate IT filler may refine internal pore-size distribution, densify matrix microstructure and suppress crack propagation. The failure mode changed from pure interfacial debonding to cohesive failure in the cement substrate. This work provides a green scheme for resource utilization of iron tailings in high-performance pavement repair materials.