Sylvain Magne

Dr. Sylvain Magne

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 August 2008 in Radiation Protection Dosimetry
Verified
Journal Article
Closed access
PDF file
SMSylvain Magne
Sylvain Magne
LAL. Auger
L. Auger
JBJ. M. Bordy
J. M. Bordy
LCL. de Carlan
L. de Carlan
AIA. Isambert
A. Isambert
JBJ. Barthe
J. Barthe
This article proposes an innovative multichannel optically stimulated luminescence (OSL) dosemeter for on-line in vivo dose verification in radiation therapy. OSL fibre sensors incorporating small Al2O3:C fibre crystals (TLD500) have been tested with an X-ray generator. A reproducible readout procedure should reduce the fading-induced uncertainty (∼− 1% per decade). OSL readouts are temperature-dependent [∼0.3% K−1 when OSL stimulation is performed at the same temperature as irradiation; ∼0.16% K−1 after thermalisation (20°C)]. Sensor calibration and depth–dose measurements with electron beams have been performed with a Saturne 43 linear accelerator in reference conditions at CEA-LNHB (ionising radiation reference laboratory in France). Predosed OSL sensors show a good repeatability in multichannel operation and independence versus electron energy in the range (9, 18 MeV). The difference between absorbed doses measured by OSL and an ionisation chamber were within ±0.9% (for a dose of about 1 Gy) despite a sublinear calibration curve.

13 May 2015
Verified
Conference Paper
Open access
PDF file
Yohan BarbarinYohan Barbarin
Yohan Barbarin
ALA Lefrancois
A Lefrancois
GZG Zaniolo
G Zaniolo
VCVincent Chuzeville
Vincent Chuzeville
LJL Jacquet
L Jacquet
AOAntoine Osmont
Antoine Osmont

14 February 2020 in Sensors
Verified
Journal Article
Open access
PDF file
Yohan BarbarinYohan Barbarin
Yohan Barbarin
LALEFRANCOIS Alexandre
LEFRANCOIS Alexandre
VCVincent Chuzeville
Vincent Chuzeville
SMSylvain Magne
Sylvain Magne
LJLaurent Jacquet
Laurent Jacquet
JLJérôme Luc
Jérôme Luc
Dynamic measurements of shock and detonation velocities are performed using long chirped fiber Bragg gratings (CFBGs). Such thin probes, with a diameter of typically 125 µm or even 80 µm can be directly inserted into high-explosive (HE) samples or simply glued laterally. During the detonation, the width of the optical spectrum is continuously reduced by the propagation of the wave-front, which physically shortens the CFBG. The light power reflected back shows a ramp-down type signal, from which the wave-front position is obtained as a function of time, thus yielding a detonation velocity profile. A calibration procedure was developed, with the support of optical simulations, to cancel out the optical spectrum distortions from the different optical components and to determine the wavelength-position transfer function of the CFBG. The fitted slopes of the X–T diagram give steady detonation velocity values which are in very good agreement with the classical measurements obtained from discrete electrical shorting pins (ESP). The main parameters influencing the uncertainties on the steady detonation velocity value measured by CFBG are discussed. To conclude, different HE experimental configurations tested at CEA (Commissariat à l’Energie Atomique et aux Energies Alternatives) are presented: bare cylindrical sticks, wedges for shock-to-detonation transitions (SDT), spheres, a cast-cured stick around a CFBG, and a detonation wave-front profile configuration.

10 March 2011 in IEEE Transactions on Nuclear Science
Verified
Journal Article
Closed access
SMSylvain Magne
Sylvain Magne
LCLoïc de Carlan
Loïc de Carlan
JBJean-Marc Bordy
Jean-Marc Bordy
AIAurélie Isambert
Aurélie Isambert
ABAndré Bridier
André Bridier
PFPierre Ferdinand
Pierre Ferdinand
A multichannel OSL fiber optic dosimeter based on optically stimulated luminescence (OSL) of alumina is proposed for online in vivo dosimetry (IVD) in radiation therapy (RT). Two types of dosimetric-grade Al2O3:C crystals are compared and show different behavior according to manufacturing process. Metrological validations have been performed with a Saturne 43 LINAC in reference conditions at CEA LIST LNHB (French Ionizing Radiation Reference Laboratory). The dose response of OSL integrals under photon beam irradiation (6, 12, and 20 MV) show sublinearity behavior modeled by second-order equations and exhibit a small energy dependence (between 0.7% and 1.4%), explained by a modified intermediate cavity model adapted to a LINAC photon spectrum. Preclinical tests at Institut Gustave Roussy (IGR) prove that a proper design for a PMMA build-up cap leads to a low dependence vs photon beam orientation (± 1.5% and ± 0.9%) and vs field size in view of surface measurements.

10 October 2018 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
SMSylvain Magne
Sylvain Magne
Yohan BarbarinYohan Barbarin
Yohan Barbarin
ALA. Lefrançois
A. Lefrançois
MBM. Balbarie
M. Balbarie
FSF. Sinatti
F. Sinatti
KWK. Woirin
K. Woirin
Fiber Bragg Gratings (FBGs) are gaining acceptance as velocity/pressure gauges in the fields of detonation and shock physics on account of their sensitivity, small size, flexibility, electromagnetic immunity, and wavelength-encoded feature. Chirped FBGs (CFBGs) are investigated as wavelength-to-position discriminators with the purpose of monitoring pressure/velocity profiles over a distance range of typically 100 mm. The use of CFBGs simplifies both sensor deployment and data retrieval and finally improves the accuracy due to the increased number of measurement data. In this paper, the metrological performance of CFBGs used as in situ distributed shock pressure/velocity gauges is investigated both theoretically and experimentally in a planar shock loading configuration with an aluminum-based flyer and target. In the intermediate range for shock stress, i.e., less than the Hugoniot Elastic Limit (HEL) of silica, CFBGs provide simultaneous measurements of both shockwave velocity and stress within the target material. A Bragg wavelength-to-stress model is proposed that takes into account (i) the state-of-stress within the target material, (ii) the stress coupling coefficient due to imperfect impedance matching between the target material and the silica fiber, (iii) the conversion of the state-of-stress into a state-of-strain within the silica fiber, and (iv) the conversion of strain data into observable Bragg wavelength shifts. Finally, the model also takes into account the pressure dependence of constitutive parameters for silica and aluminum. Experiments were performed in planar shock loading using CFBGs as stress gauges, bonded along the target axis with Araldite glue. 6061-T6 aluminum flyers were launched at several velocities by a gas gun onto targets of the same material. A free-space Czerny-Turner (CT) spectrometer and an integrated-optics Arrayed-Waveguide Grating (AWG) were both used as dynamic spectrum analyzers. Experimental Bragg wavelength shifts agree well with theoretical predictions for both elastic and hydrodynamic planar shock loading of 6061-T6 aluminum, opening up large perspectives for shock physics experiments.

10 June 2022 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
SMSylvain Magne
Sylvain Magne
NLN. Legrand
N. Legrand
SES. Ertz
S. Ertz
GJG. Jouvin
G. Jouvin
VAV. André
V. André
LBL. Boissonnet
L. Boissonnet
The shape of laminated products is a crucial parameter in high-speed and high-volume finishing lines where they must fulfill tight tolerances. Latent defects are detected by flatness rolls (or shapemeter rolls) inserted in the manufacturing line for online flatness control. A prototype of flatness roll has been developed with high spatial resolution (5 mm) and measurement capability over a thickness range of 0.1–1 mm to evaluate flatness and residual stresses of flat metal strip products manufactured by continuous cold rolling (ultra-thin sheets for packaging and automotive markets). The flatness roll prototype relies on pressure-induced strain sensing on segmented blades using Fiber Bragg Grating technology. Synchronous measurement of the flatness profile across strip width rejects disturbances of strip tension during rolling. We provide a proof-of-concept on pilot lines in both static and dynamic conditions (e.g., roll in rotation and in contact with a strip under tension) and the sensing mechanism shows a capability above 3. This combination of performances remains unique up to now. Interblade crosstalk appears to be an important issue. We propose a crosstalk model that agrees with experimental coupling coefficients. A crosstalk matrix inversion yields the distribution in contact pressure from strain data measured on the reverse side. Additional work will be required to use the flatness roll in industrial conditions.