This work provides a comprehensive view on how multiple mechanical cues of the substrate influence fundamental cellular processes, including spreading, proliferation, migration and differentiation, towards 3D tissue constructs.

The European steel industry produces about 70 million tons/year of steel by the electric arc furnace (EAF). The slag consists of about 15% by weight of the produced steel, thus from the perspective of the circular economy, it has a high potential as a co-product. This research aims to assess an innovative reuse of EAF slag as filler in different polymer matrixes: thermoplastic (polypropylene), thermosetting (epoxy resin), elastomeric (nitrile butadiene rubber), and recycled end of life rubber tire. A comparison between neat polymer and polymer filled with a certain amount of EAF slag has been carried out by tensile (or flexural), compression, and hardness tests. Experimental results show that slag as a filler increases the composites’ hardness and elastic modulus at the expense of toughness. For a safe reuse of the slag, the leaching of hazardous elements must comply with current legislation. It was found that, although the used EAF slag releases small amounts of Cr, Mo, and V, incorporating it into a polymer matrix reduces the leaching. The EAF slag particles distribution has been observed by scanning electron microscopy (SEM) images. The obtained results show good technical feasibility of this innovative slag application so that it could pave the way to a new industrial symbiosis between dissimilar sectors, bringing economic and environmental benefits.

This work reports and analyzes the mechanical properties of some composites obtained using stabilized waste with epoxy resins E-227. For comparison, correspondent composite samples were realized using calcite as a filler. The recovered stabilized waste was obtained by means of a new method to stabilize municipal solid waste incineration (MSWI) fly ash (FA), based on the use of bottom ash (BA). The aim of this paper is to show that the stabilization process, which can be considered a zero—waste treatment, produces inert materials, that can be reused as a filler. The production of new filler was made on a pilot plant, designed to verify the transferability of the proposed stabilization technology. Mechanical analysis revealed that flexural modulus raises by increasing the filler content around 30% wt, independently of filler type, stabilized sample or calcium carbonate. Mechanical properties are lower in the samples with the high amount of filler due to the crowding effect. The morphology of composite materials showed a non-homogeneous dispersion of particles in stabilized sample filler, characterized by large particle agglomerates. Finally, according to the ESCAPE simplified method, the obtained composites result more sustainable in comparison with the corresponding ones produced by using natural resources (like calcite). These findings open new possibilities for the reuse of the stabilized material, in frame of circular economy principles, with environmental and economic advantages.

Environmental stress cracking is a serious problem for polyethylene because it can cause failure without any visible warning due to the slow crack growth accelerated by aggressive agents. Tie molecules and entanglements are the main macromolecular characteristic increasing environmental stress cracking resistance, thus in this work mechanical and thermal properties governed by those macromolecular characteristics are determined by performing simple tests executable in the industrial laboratories for quality control on recycled high-density polyethylene. The mutual relation between the determined properties confirms their dependence on the investigated macromolecular characteristics and allows to predict in a comparative way the expected environmental stress cracking. The mechanical properties related to the environmental stress cracking resistance are the strain hardening modulus and the natural draw ratio. The strain hardening modulus is an intrinsic property that measure the disentanglement capability of the inter-lamellar links and the natural draw ratio is a highly sensitive parameter to the macromolecular network strength via the intercrystalline tie molecules. Since the measurement of these properties according to the standard ISO 18,488 requires a temperature chamber not often available in the industrial laboratories, the tensile test was performed also at room temperature and displacement rate 0.5 mm/min; a proportionality between the data obtained at different test condition emerged. The thermal property related to the environmental stress cracking resistance is the stepwise isothermal segregation ratio that state the chain fraction that generates a high rate of tie molecules responsible of environmental stress cracking resistance.

Conductive nanocomposites play a significant role in tissue engineering by providing a platform to support cell growth, tissue regeneration, and electrical stimulation. In the present study, a set of electroconductive nanocomposite hydrogels based on gelatin (G), chitosan (CH), and conductive carbon black (CB) was synthesized with the aim of developing novel biomaterials for tissue regeneration application. The incorporation of conductive carbon black (10, 15 and 20 wt.%) significantly improved electrical conductivity and enhanced mechanical properties with the increased CB content. We employed an oversimplified unidirectional freezing technique to impart anisotropic morphology with interconnected porous architecture. An investigation into whether any anisotropic morphology affects the mechanical properties of hydrogel was conducted by performing compression and cyclic compression tests in each direction parallel and perpendicular to macroporous channels. Interestingly, the nanocomposite with 10% CB produced both anisotropic morphology and mechanical properties, whereas anisotropic pore morphology diminished at higher CB concentrations (15 and 20%), imparting a denser texture. Collectively, the nanocomposite hydrogels showed great structural stability as well as good mechanical stability and reversibility. Under repeated compressive cyclic at 50% deformation, the nanocomposite hydrogels showed preconditioning, characteristic hysteresis, nonlinear elasticity, and toughness. Overall, the collective mechanical behavior resembled the mechanics of soft tissues. The electrical impedance associated with the hydrogels was studied in terms of the magnitude and phase angle in dry and wet conditions. The electrical properties of the nanocomposite hydrogels conducted in wet conditions, which is more physiologically relevant, showed a decreasing magnitude with increased CB concentrations, with a resistive-like behavior in the range 1 kHz–1 MHz and a capacitive-like behavior for frequencies 1 MHz. Overall, the impedance of the nanocomposite hydrogels decreased with increased CB concentrations. Together, these nanocomposite hydrogels are compositionally, morphologically, mechanically, and electrically similar to native ECMs of many tissues. These gelatin-chitosan–carbon black nanocomposite hydrogels show great promise for use as conducting substrates for the growth of electro-responsive cells in tissue engineering.

The amount of rubber scraps derived from rubber goods production consists of about 20–30% of the processed material, so it is necessary to enhance this material by developing new recycling techniques as well as a new market for recycled rubber products. In the present research, nitrile-butadiene rubber (NBR) scraps are reprocessed via a calendering process acting with a mechanical devulcanization. Compounds were prepared with 20%, 80%, and 100% recycled rubber content and characterized. The experimental results highlighted that the compound prepared with 20% recycled rubber content via calendering and compression molding processes shows comparable mechanical properties to that of virgin NBR. The tensile properties are the most penalized by the increasing content of recycled material (100% recycled shows − 25% and − 50% stress and strain at break, respectively). Other properties remain comparable to the standard material up to 80% recycled material: 60 ± 5 Shore A, compression elastic modulus 8 MPa, compression set 20%. FTIR analysis revealed no changes in chemical structure from the recycling process. The results demonstrate that simple mechanical devulcanization can effectively reprocess industrial rubber waste while largely maintaining useful properties. This provides a potential pathway to enhance sustainability in rubber production through the valorization of process scraps. Graphical Abstract