Fatma Zohra Saidoune

Dr. Fatma Zohra Saidoune

orcid

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 July 2026 in Processes
Verified
Journal Article
Open access
PDF file
STSouad TAHAR
Souad TAHAR
FSFatma Zohra Saidoune
Fatma Zohra Saidoune
FDFaouzi Didi
Faouzi Didi
MZMounir Zirari
Mounir Zirari
HYHichem Ykrelef
Hichem Ykrelef
Elsayed EEElsayed EE
Elsayed EE
Optimizing fuel injector geometry represents a critical pathway toward cleaner and more efficient diesel combustion. This study presents a comprehensive numerical investigation of the influence of the dual-hole nozzle injection angle on the primary atomization behavior and spray hydrodynamics of high-pressure diesel jets. The present analysis is deliberately restricted to cold-flow, near-nozzle primary breakup under isothermal conditions (293.15 K) so that the hydrodynamic and aerodynamic breakup mechanisms can be isolated in the immediate vicinity of the orifice before evaporation and combustion occur. Two-dimensional simulations are conducted using an Eulerian Volume-of-Fluid (VOF) framework with finite element discretization, three injection-angle configurations (0°, 5°, and 10°) under realistic engine conditions (injection pressure: 138 MPa; chamber pressure: 2.32 MPa; nozzle diameter: 100 µm). The numerical model was validated against the experimental and computational benchmark data of Ménard et al., showing reasonable qualitative agreement in jet morphology, although the 2D nature of the model leads to an exaggerated accumulation of liquid at the spray tip compared to the 3D reference. The validation therefore supports the qualitative trends and the relative angular comparison, but the absolute quantitative predictions remain subject to this 2D structural limitation. Results reveal that the injection angle exerts a decisive influence on the competition between axial momentum and radial dispersion. The neutral 0° configuration yields an overly concentrated jet with limited interfacial destabilization and poor air entrainment, whereas the 10° angle produces excessive radial spreading at the expense of axial penetration depth. By contrast, the 5° convergence angle provides the best trade-off among the three tested configurations under the studied conditions, promoting enhanced Rayleigh–Plateau instability growth, earlier ligament formation, and finer droplet generation—favorable to a more homogeneous air–fuel mixture. These findings provide quantitative guidance for dual-hole injector geometry design and demonstrate the suitability of high-fidelity VOF-based methods for resolving complex two-phase atomization phenomena relevant to low-emission diesel engine design. Quantitatively, the peak axial velocity is reached at the nozzle exit for all configurations; relative to the 0° baseline, the 5° convergence angle increases the fuel–air interfacial spreading by about 141% while retaining roughly 90% of its axial penetration at the monitoring positions P1–P3, whereas the 10° case loses about 26% of axial penetration for a comparable radial spread.

27 October 2026 in Processes
Verified
Journal Article
Open access
PDF file
FSFatma Zohra Saidoune
Fatma Zohra Saidoune
STSouad TAHAR
Souad TAHAR
KHKawthar HADJA
Kawthar HADJA
HYHichem Ykrelef
Hichem Ykrelef
MZMounir Zirari
Mounir Zirari
Elsayed EEElsayed EE
Elsayed EE
This study investigates entropy generation in a steady, laminar, magnetohydrodynamic mixed-convection boundary-layer flow of a hybrid Cu–Al2O3/water nanofluid over a heated, slender vertical cylinder subjected to a transverse magnetic field, Joule heating, viscous dissipation and thermal radiation. The governing partial differential equations are reduced to a non-similar system via a local-Reynolds-number similarity transformation and solved using a finite-difference collocation boundary-value method (bvp4c) combined with ξ-continuation and a second-level local non-similarity formulation. The model is validated against previously published results with deviations of about 2% over the range of curvature considered. Results show that the applied magnetic field decelerates the flow and increases the local entropy generation, while increased buoyancy accelerates the flow and enhances wall heat transfer. Thermal radiation and Joule heating both thicken the thermal boundary layer. Quantitatively, as the radiation parameter Rd increases from 0 to 2, the local Nusselt number rises from 0.9283 to 2.4103 (at Ri=1, M=0.5, ξ=1); as the Richardson number Ri increases from 0 to 2, the skin-friction coefficient rises from 0.9477 to 1.7798. The Brinkman number is identified as the dominant parameter controlling the balance between heat transfer and Joule irreversibility, as quantified through the entropy generation number and the Bejan number. These findings provide guidance for the thermal design and second-law optimization of MHD hybrid-nanofluid systems operating over curved geometries.