Models are necessary tools for watershed management. However, applying watershed models is time consuming and requires technical knowledge, including model selection and validation. The objective of this study is to assess two commonly used watershed models and their parameter sensitivity to reduce model loadings and to gain a better understanding of the model performances. The Hydrological Simulation Program-Fortran (HSPF) model and Storm Water Management Model (SWMM) were applied to a mostly forested Taiwanese reservoir watershed with pollution from tea plantations. Statistical analysis showed that both models are suitable for the studied watershed, but the performances of the flow and water quality simulations are different. The mean flow simulated by SWMM was lower than the experimental observations. The HSPF model performed better, possibly because the soil in the study area is highly permeable and the HSPF model has more precise soil layer calculations. SWMM may underestimate the total phosphorous (TP) and suspended solid (SS) loads following small storm events in highly permeable watersheds. The Latin Hypercube-One factor At a Time (LH-OAT) method was used to determine the parameter sensitivity of the HSPF model and SWMM. In both of the models, the parameters related to infiltration and soil characteristics strongly affected the flow simulation, except when using the Horton infiltration method in the SWMM. Manning’s roughness coefficient for pervious areas was more sensitive in SWMM than in the HSPF model because SWMM has fewer parameters.
Low impact development (LID) is a relatively new concept in land use management that aims to maintain hydrological conditions at a predevelopment level without deteriorating water quality during land development. The United States Environmental Protection Agency (USEPA) developed the System for Urban Stormwater Treatment and Analysis Integration model (SUSTAIN) to evaluate the performance of LID practices at different spatial scales; however, the application of this model has been limited relative to LID modeling. In this study, the SUSTAIN model was applied to a Taiwanese watershed. Model calibration and verification were performed, and different types of LID facilities were evaluated. The model simulation process and the verified model parameters could be used in other cases. Four LID scenarios combining bioretention ponds, grass swales, and pervious pavements were designed based on the land characteristics. For the SUSTAIN model simulation, the results showed that pollution reduction was mainly due to water quantity reduction, infiltration was the dominant mechanism and plant interception had a minor effect on the treatment. The simulation results were used to rank the primary areas for nonpoint source pollution and identify effective LID practices. In addition to the case study, a sensitivity analysis of the model parameters was performed, showing that the soil infiltration rate was the most sensitive parameter affecting the LID performance. The objectives of the study are to confirm the applicability of the SUSTAIN model and to assess the effectiveness of LID practices in the studied watershed.
Low-impact development (LID) structures are widely used to mitigate urbanization impacts on hydrology. The performances of such structures are strongly affected by field conditions, such as the ratio of LID area to drainage area and rainfall properties, such as rainfall intensity. In this study, onsite continuous monitoring was performed at a permeable pavement site and a raingarden site in Taipei, Taiwan, to determine their water retention and groundwater recharge potential under subtropical weather. In addition, the verified Storm Water Management Model (SWMM) was used to illustrate the annual performance on the hydrological cycle. Based on one year of monitoring, data on 41 and 24 rainfall events were obtained at the permeable pavement and raingarden sites, respectively. The ratio of the permeable pavement area to the total drainage area was 36.0%, and this ratio was 15.9% for the raingarden. The results showed that the average runoff reduction rate was 14.7% at the permeable pavement site, and 98.3% of the rainfall was retained in the raingarden and an underground storage tank. The validated model showed that the permeable pavement site experienced 45.3% outflow, 31.6% evaporation, and 23.1% infiltration annually. For the raingarden with an underground storage tank, 91.4% of the annual rainfall infiltrated and was stored, with only 4.1% outflow. According to the observed rainfall event performance and the simulated annual performance, the permeable pavement and raingarden performed well in subtropical regions. Pavement that was approximately 1/3 permeable in a drainage area increased infiltration by approximately 20%, and a raingarden with a sufficient underground storage tank preserved over 90% of the rainfall.
Pollutants deposited on road surfaces and distributed in the environment are a source of nonpoint pollution. Field data are traditionally hard to collect from roads because of constant traffic. In this study, in cooperation with the traffic administration, the dry deposition on and road runoff from urban roads was measured in Taipei City and New Taipei City, Taiwan. The results showed that the dry deposition is 2.01–5.14 g/m2·day and 78–87% of these solids are in the 75–300 µm size range. The heavy metals in the dry deposited particles are mainly Fe, Zn, and Na, with average concentrations of 34,978, 1,519 and 1,502 ppm, respectively. Elevated express roads show the highest heavy metal concentrations. Not only the number of vehicles, but also the speed of the traffic should be considered as factors that influence road pollution, as high speeds may accelerate vehicle wear and deposit more heavy metals on road surfaces. In addition to dry deposition, the runoff and water quality was analyzed every five minutes during the first two hours of storm events to capture the properties of the first flush road runoff. The sample mean concentration (SMC) from three roads demonstrated that the first flush runoff had a high pollution content, notably for suspended solid (SS), chemical oxygen demand (COD), oil and grease, Pb, and Zn. Regular sweeping and onsite water treatment facilities are suggested to minimize the pollution from urban roads.
Low-impact development (LID) aims to retain stormwater at source sites rather than achieve water drainage. The infiltration and storage of rainwater on site is the most commonly applied LID design concept, turning impervious pavements into pervious pavements. In this study, three field sites in Taipei city, Taiwan, were monitored. Two of the sites were located on campuses, and one site was a roadside location. They were constructed at different times and had distinct purposes, but the common design aspect was the infiltration function of the ground surface. We monitored the water retention performance at the above three sites and applied a verified stormwater management model (SWMM) to characterize the performance at these case sites. The observed data show that if the accumulative rainfall was lower than 20 mm, the water retention rate at each of the three case sites reached almost 50%; at 60 mm rainfall, the rate was 40%. With increased rainfall amount, the water retention rate decreased because the storage capacity was limited. Because water retention is typically controlled by the infiltration capacity, the rainfall intensity dominated the performance. At the three field sites, the water retention rate was 40% on average at a rainfall intensity below 20 mm/h. Above this rainfall intensity, the infiltration performance of the pervious pavement decreased. The verified model was applied to assess the performance at the three sites under the Taipei city drainage system design standard, i.e., the five-year recurrent period storm level, at 78.8 mm/h. The results demonstrate that the water retention rates were 9.1%, 14.2%, and 61.0% at the three sites, indicating that the pervious pavement could reduce the loading of the current stormwater drainage system. Dispersed sites should be considered in urban stormwater management to mitigate flooding risk in urban areas.
Total maximum daily loads (TMDLs) are used to protect water bodies based on their assimilative ability and are transferred as a maximum allowable load, which is the sum of all pollution emissions in a watershed that cannot be exceeded. This allowable load is calculated from a target water quality concentration and a flow state. The target water quality concentration is typically consistent with water quality standards; however, it is difficult to determine which flow state to use, especially for lakes and reservoirs. In this study, an exceedance probability method is established for determining the TMDL for reservoirs. The SWMM (Storm Water Management Model) was used to understand the pollution loads from the watershed, and the Vollenweider model was used to simulate the total phosphorous (TP) concentrations in the reservoir. Using the validated Vollenweider model, the relationship between pollution loads and the target TP concentration is illustrated. This relationship is associated with real changes in the reservoir water volume and is presented as the exceedance probability. In the study area (i.e., the Shiman Reservoir in Taiwan), an exceedance probability of 50% is suggested, and the allowable TP load is 22,209 kg/year when considering a target TP concentration of 20 μg/L. When considering effective management, the pollution sources in three hot spots are priorities, and controlling their point and nonpoint pollution sources can decrease TP from 25 to 22 μg/L.