Kaythar Abdulwahab Ibrahim

Kaythar Abdulwahab Ibrahim

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 August 2023 in Cogent Engineering
Verified
Journal Article
Open access
MSMohammed H. Shukur
Mohammed H. Shukur
KIKaythar Abdulwahab Ibrahim
Kaythar Abdulwahab Ibrahim
SASuhaib Yahya Al-Darzi
Suhaib Yahya Al-Darzi
Oday Asal SalihOday Asal Salih
Oday Asal Salih

8 October 2024 in Tikrit Journal of Engineering Sciences
Verified
Journal Article
Open access
PDF file
SASuhaib Y.K. Al-Darzi
Suhaib Y.K. Al-Darzi
KIKaythar Abdulwahab Ibrahim
Kaythar Abdulwahab Ibrahim
Oday Asal SalihOday Asal Salih
Oday Asal Salih
In the present study, eight reinforced concrete slabs divided into four groups with two slabs per group were fabricated and tested under impact load, replacing their aggregate with 0%, 4%, 8%, and 16% of polyethylene terephthalate) PET). During the preparation process, PET materials increased the workability of fresh concrete by up to 16% and decreased the density by 9%. The compressive strength decreased by about 11.7%, 15.7%, and 19.9% using 4%, 8%, and 16% of PET, respectively. Splitting strength decreased by 7.2%, 17.4%, and 20.3% using 4%, 8%, and 16% of PET, respectively. Failure mode and deflection amplitude results showed that PET delayed the first cracks and reduced the crack lengths and width and crack spreading at failure. Also, impact resistance enhanced at the first crack and ultimate load stages when PET was used compared to normal concrete. The maximal and minimal displacement decreased with increasing PET proportion to 8% and 16%. The slabs were modeled using the finite element program SAP2000 with 4-node shell elements. The finite element (FE) analysis showed a similar deflection response as those experimentally obtained for all slabs. The deflection obtained by FE was less, about 15.5% and 19%, compared with all slabs experimentally tested except slab G2-2, which showed a higher deflection of about 16.3%.

1 January 2023 in Open Engineering
Verified
Journal Article
Open access
PDF file
KIKaythar Abdulwahab Ibrahim
Kaythar Abdulwahab Ibrahim
SASuhaib Y. Al-Darzi
Suhaib Y. Al-Darzi
MSMohammed H. Shukur
Mohammed H. Shukur
Reinforced concrete skew slabs are commonly used in bridges due to space constraints in motorways and in congested urban areas. Such slabs also often need to contain openings for architectural requirements or services, and this study seeks to determine the effect of these openings on the strength of the skew slabs. The finite element method was used to analyze 13 cases of slabs with skew angles of 45°. The first and second cases were used to validate the results with experimental work. Other cases studied the effect of the position and shape of openings on the strength of the skew slabs under both one-point and four-point loading conditions. The study also showed that the worst location for the opening was near the obtuse corners since this is where most of the load is transferred. With respect to the shape of openings, three different shapes with the same area were used: skew, circle, and square shapes. It was found that the effect of the opening shape depends on how many steel reinforcements are removed, as well as the appearance of negative cracking brought on as a result of the opening. Overall, the square shape introduces the smallest reduction in the skew slab strength compared with a slab with no opening. Accordingly, the study recommends that the strength of skew slabs can best be maintained if square openings are employed near the acute corners, alongside negative steel reinforcement to avoid cracking.

14 August 2026 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
Oday Asal SalihOday Asal Salih
Oday Asal Salih
KIKaythar Abdulwahab Ibrahim
Kaythar Abdulwahab Ibrahim
MSMohammmed Husham Shukur
Mohammmed Husham Shukur
SASuhaib Y.K. Al-Darzi
Suhaib Y.K. Al-Darzi
SASofyan Y. Ahmed
Sofyan Y. Ahmed
Accidental web openings caused by impact, corrosion, or conflict-related damage can substantially reduce the strength, stiffness, and stability of steel bridge girders. Although numerous studies have examined beams containing intentionally designed web openings, limited experimental research has systematically compared practical rehabilitation methods for accidental openings in slender-web plate girders. This study experimentally and numerically evaluates several rehabilitation configurations incorporating welded patch plates and transverse stiffeners. Ten slender-web steel girder specimens, each 1800 mm long, 800 mm deep, and 300 mm wide, were tested under monotonic concentrated loading at mid-span. Nonlinear finite element models were also developed to qualitatively examine the principal deformation and instability trends. Relative to the control specimen, the untreated web opening reduced the ultimate load by approximately 43% and exhibited approximately 10% greater deflection at its respective ultimate load. One-sided and two-sided welded patch plates increased the ultimate load of the damaged specimen by approximately 22% and 26%, respectively. Transverse stiffeners increased the ultimate load by approximately 73% while exhibiting substantially lower ultimate-load deflections. The combined use of patch plates and transverse stiffeners provided the greatest improvement, increasing the ultimate load by approximately 101–123% relative to the untreated damaged specimen and substantially reducing lateral instability. The findings demonstrate that effective rehabilitation of slender-web girders requires not only restoration of the interrupted load path but also restraint of web instability.

21 October 2026 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
MSMohammmed Husham Shukur
Mohammmed Husham Shukur
Oday Asal SalihOday Asal Salih
Oday Asal Salih
KIKaythar Abdulwahab Ibrahim
Kaythar Abdulwahab Ibrahim
SASuhaib Y.K. Al-Darzi
Suhaib Y.K. Al-Darzi
This study experimentally and numerically investigates how skew angle affects the structural behavior of reinforced concrete slabs under monotonic and repeated loading. Eight simply supported slab specimens were divided into four groups corresponding to skew angles of 0°, 15°, 30°, and 45°, with one specimen in each group tested under monotonic loading and the other under repeated loading. All specimens had plan dimensions of 1400 × 1400 mm and a thickness of 100 mm and were subjected to a concentrated load at mid-span. The repeated-loading protocol consisted of stepwise quasi-static loading–unloading cycles with the peak load increased by 5 kN in each successive cycle until failure. All specimens exhibited predominantly flexural failure, with major cracking concentrated within the middle region of the slabs. The first-cracking loads under repeated loading were approximately 9.1–12.0% lower than those of the corresponding monotonic specimens. The effect of repeated loading on yield and ultimate response depended on skew angle and did not exhibit a uniform trend. However, increasing skew angle generally reduced load resistance and increased deformation. Under repeated loading, the ultimate load decreased by approximately 13.2%, 27.6%, and 33.1% for skew angles of 15°, 30°, and 45°, respectively, relative to the zero-skew specimen. Under monotonic loading, the 45° specimen exhibited approximately 24.9% lower ultimate resistance than the zero-skew specimen. The displacement ductility response was non-monotonic; under monotonic loading, maximum ductility occurred at 30°, and under repeated loading, at 15°. A simplified equivalent-strip analytical model was used as a preliminary reference, while three-dimensional nonlinear finite-element models were developed using ANSYS. The finite-element predictions of ultimate load differed from the experimental results by approximately 5.6–15.2%, although larger differences were observed in the load–deflection response and crack distribution. Overall, the experimental findings suggest that skew angle and loading history may influence deformation, stiffness, and ultimate resistance. However, since only one specimen was tested for each configuration, the reported differences should be considered descriptive observations rather than statistically validated relationships. Further experimental investigations with replicate specimens are required to confirm these trends.

1 April 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
MSMohammed H. Shukur
Mohammed H. Shukur
Oday Asal SalihOday Asal Salih
Oday Asal Salih
KIKaythar Abdulwahab Ibrahim
Kaythar Abdulwahab Ibrahim
SASuhaib Y.K. Al-Darzi
Suhaib Y.K. Al-Darzi
In the present work, an experimental investigation was conducted for 8 groups of skew slabs, with 0, 15, 30 and 45 skew angles, with one slab for each group under monotonic and repeated loads. The simple span slab specimens with dimensions of 1400x1400x100 mm, supported from two sides, were tested using concentrated loads at mid-span. The mode of failure for each slab investigated showed that flexural failure with cracks at the middle third appeared for all specimens. It was found that the first cracking loads decreased with the increase of skew angle and decreased when a repeated load was compared with a monotonic load with a larger deflection. The present work concluded that the yield and ultimate loads decreased by increasing the skew angle, and the deflection increased. It was also found that the repeated load causes a decrease in yield and an increase in deflection. The work includes calculations for the theoretical loads and deflection, and the results obtained for skew slabs are less than those experimentally obtained. The ductility index is estimated and shows that increasing the skew angle will increase the ductility of the slab. Additionally, the use of repeated loads decreases the ductility of the skew sl