This study aimed to validate the single-phase and two-phase smoothed particle hydrodynamics (SPH) on sloshing in a tank. There have been many studies on sloshing in tanks based on meshless particle methods, but few researchers have used a large number of particles because there is a limitation on the total number of particles when using only CPUs. Additionally, few studies have investigated the influence of air phase on tank sloshing based on two-phase SPH. In this study, a dedicated sloshing experiment was conducted at the National Research Institute of Fishing Engineering using a prismatic tank with a four-degrees-of-freedom forced oscillation machine. Three pressure gauges were used to measure local pressure near the corners of the tank. The sloshing experiment was repeated for two different filling ratios, amplitudes, and frequencies of external oscillation. Next, a GPU-accelerated three-dimensional SPH simulation of sloshing was performed using the same conditions as the experiment with a large number of particles. Lastly, two-dimensional sloshing simulations based on single-phase and two-phase SPH were carried out to determine the importance of the air phase in terms of tank sloshing. Based on systematic comparisons of the single-phase SPH, two-phase SPH, and experimental results, this paper presents a detailed discussion of the role of air-phase in terms of sloshing. The currently achievable accuracy when using SPH is demonstrated together with a few sensitivity analyses of SPH parameters.
Spray strips are deflectors added to the hull to reduce the Wetted Surface Area (WSA). The reduced WSA will decrease the total ship drag caused by the deflection of the spray strip installation. The research aimed to predict the function of the spray strip to improve ship performance using Computational Fluid Dynamics (CFD). The numerical approach in this study used the Finite Volume Method (FVM) with the RANS (Reynolds-averaged Navier–Stokes) equation to solve fluid dynamics problems. VOF (Volume of Fluid) was used to model the water and air phases. The results of this study indicated that the number of spray strips would have a significant effect compared to without using a spray strip. Spray strips with three strips could reduce the total resistance by 4.9% at Fr 1.78. Spray strips would increase the total resistance value by 2.1% at low speeds. Spray strips were effective for reducing total resistance at Fr > 1 or the planing mode conditions. The total resistance prediction used three suggestion profiles with the best performance to reduce total resistance by 6.0% at Fr 1.78.
This paper is aimed to validate smoothed particle hydrodynamics (SPH) on the generation and propagation of water waves. It is a classical problem in marine engineering but a still important problem because there is a strong demand to generate intended nonlinear water waves and to predict complicated interactions between nonlinear water waves and fixed/floating bodies, which is indispensable for further ocean utilization and development. A dedicated experiment was conducted in a large wave basin of Kobe University equipped with a piston-type wavemaker, at three water depths using several amplitudes and periods of piston motion for the validation of SPH mainly on the long-distance propagation of water waves. An SPH-based two-dimensional numerical wave tank (NWT) is used for numerical simulation and is accelerated by a graphics processing units (GPU), assuming future applications to realistic engineering problems. In addition, comparison of large-deformation of shallow water waves, when passing over a fixed box-shape obstacle, is also investigated to discuss the applicability to wave-structure interaction problems. Finally, an SPH-based three-dimensional NWT is also validated by comparing with an experiment and two-dimensional simulation. Through these validation studies, detailed discussion on the accuracy of SPH simulation of water waves is made as well as providing a recommended set of SPH parameters.
4 June 2020 in Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan
The sloshing phenomenon is one of the free surface flow that can endanger liquid cargo carriers such as ships. Sloshing is defined as the resonance of fluid inside a tank caused by external oscillation. When sloshing is close to the natural frequency of the tank it could endanger ships. Particle method has the advantages to be applied because sloshing is dealing with free surface. One of the particle methods is Smoothed Particle Hydrodynamics (SPH). In this study, compressible SPH was used as a result of the pressure oscillation, which exists because of the effect of density fluctuation as nature of weakly compressible SPH. To reduce pressure noise, a filtering method, Low Pass Filter, was used to overcome pressure oscillation. Three pressure sensors were used in the sloshing experiment with a combination of motions and filling ratios. Only one pressure sensor located in the bottom was used to validate the numerical results. A set of SPH parameters were derived that fit for the sloshing problem. The SPH results show a good agreement with the experiment’s. The difference between SPH and experiment is under 1 % for sway, but a larger difference shows in roll. Low pass filter technique could reduce pressure noise, but comprehensive method needs to develop for general implementation.
The patrol boat is one of the critical aspects for archipelago countries, such as Indonesia, to supervise and maintain the sea border. Due to rough sea conditions, the patrol boat could lose its stability due to the loss of a self-righting roll moment in severe waves. One of the most challenging aspects is to ensure the sufficient stability of the patrol boat during rough conditions. Another challenge is to design a boat that has a self-righting moment during rolling in extreme conditions. This paper examines the design of an anti-capsize ship by improving the self-righting moment with different deck houses height. The rough condition is described when the boat experiences a roll angle of 170°. The principal dimensions of the patrol boat, i.e., Lpp, B, H, T, are 13.0 m, 4.2 m, 2.19 m, and 1.15 m, respectively. Four different deck house heights are compared to obtain the best self-righting roll moment with a height increment of 0.1 m. The physical model is implemented with ship model 1:27.4. In addition, computational fluid dynamics (CFD) is also used to support the proof of the existence of the self-righting roll moment. It is revealed that the center of gravity and buoyancy are essential parameters to acquire the self-righting moment. The height of the deckhouse improves the center of the metacenter, which influences the righting arm of ship stability. The results show that our ship design has a self-righting moment during heel at 180°.
This paper presents an optimisation study to determine the best centre of gravity (CoG) position to improve seakeeping performance. Two varied parameters used in this study were the longitudinal and vertical centre of gravity (LCG and VCG). The Radius Gyration in the y-axis () is introduced as a novel single-objective function to be minimised, avoiding the complexity of the conventional seakeeping optimisation process. The quality of the seakeeping performance was evaluated by response amplitude operators (RAOs) of the heave, pitch, and vertical motion. Two different hull forms are compared to investigate the applicability of the as the objective function in seakeeping optimisation. The patrol boat and S-60 hull form are selected as representatives of a planing hull type and a displacement hull type. The optimisation was carried out by using the Central Composite Design (CCD) and response surface methodology (RSM) to model the relationship between the CoG and from large and small vessels, with the objective function minimising the . The finding shows that minimising the is more sensitive to the planing hull type compared to the displacement hull type in reducing the vertical motion in different Froude numbers and wave headings.