Patient-specific studies on vascular flows have significantly increased for hemodynamics due to the need for different observation techniques in clinical practice. In this study, we investigate aortic aneurysms in terms of deformation, stress, and rupture risk. The effect of Ascending Aortic Diameter (AAD) was investigated in different aortic arches (19.81 mm, 42.94 mm, and 48.01 mm) via Computational Fluid Dynamics (CFD), Two-way coupling Fluid–Structure Interactions (FSI) and deep learning. The non-newtonian Carreau viscosity model was utilized with patient-specific velocity waveform. Deformations, Wall Shear Stresses (WSSs), von Mises stress, and rupture risk were presented by safety factors. Results show that the WSS distribution is distinctly higher in rigid cases than the elastic cases. Although WSS values rise with the increase in AAD, aneurysm regions indicate low WSS values in both rigid and elastic artery solutions. For the given AADs, the deformations are 2.75 mm, 6. 82 mm, and 8.48 mm and Equivalent von Mises stresses are 0.16 MPa, 0.46 MPa, and 0.53 MPa. When the rupture risk was evaluated for the arteries, the results showed that the aneurysm with AAD of 48.01 mm poses a risk up to three times more than AAD of 19.81 mm. In addition, an Artificial neural network (ANN) method was developed to predict the rupture risk with a 98.6% accurate prediction by numerical data. As a result, FSI could indicate more accurately the level of rupture risk than the rigid artery assumptions to guide the clinical assessments and deep learning methods could decrease the computational costs according to CFD and FSI.
1 February 2019 in Sakarya University Journal of Science
Recently, the studies in the automotive sector has concentrated on hybrid electric vehicle. The better results in fuel economy and vehicle performance values have been achieved with the hybrid electric vehicle technology. In this study, the fuel consumption and vehicle performance values are compared to the series and parallel hybrid electric modes of a conventional street sweeper by using AVL Cruise. Nowadays, there are many driving cycles used in the analysis of fuel consumption and vehicle performans. However the current driving cycles are not appropriate for the vehicles designed for a particular function (carrying, lifting, sweeping etc.) such as street sweepers in terms of velocity and functionality. For this reason, a driving cycle was constructed by taking into consideration the daily tasks of the street sweepers with the help of AVL Cruise. The series and parallel hybrid electric configurations of the street sweeper were analyzed separately. Consequently, the demanded power (kW) from the internal combustion engine and its fuel consumption (L/h) were investiageted under the specific operating conditions in the driving cycle. The simulations show that the series hybrid mode has better fuel economy and vehicle performance.
7 October 2023 in Journal of Mechanics in Medicine and Biology
Recent research has focused significantly on the rising energy demand and advancements in heat exchangers, which are effective in heat transfer. This study examines the counter-flow Double Pipe Heat Exchanger (DPHE) under various flow, geometric, and thermal conditions using water-based nanofluids via Computational Fluid Dynamics (CFD). The objective of this research is to investigate the heat transfer performance in DPHEs, employing the effectiveness-NTU method for theoretical validation. Additionally, this study incorporates widely used water-based nanofluids with Al 2 O 3 , CuO, and hexagonal Boron Nitride (h-BN) nanoparticles at varying volume fractions to improve heat transfer. Several cases are designed to assess and compare thermal performance in heat exchangers using CFD. An Artificial Neural Network (ANN) model is developed in Python, integrating MATLAB to estimate thermal performance using the Overall Heat Transfer Coefficient ( U ). The findings revealed that h-BN nanofluids demonstrated outstanding heat transfer performance in different nanoparticles used in this study. The h-BN showed superior thermal performance compared to water and the other water-based Al 2 O 3 and CuO nanofluids. Comparisons with theoretical calculations validated the precision of the CFD simulation outcomes. Under the same conditions, it was observed that Al 2 O 3 increased U values by up to 20%, CuO by up to 15%, and h-BN by up to two times compared to water samples. The effectiveness method is in good agreement with CFD results. The constructed ANN model predicts heat transfer performance with an accuracy of 98.3% when compared with numerical and theoretical results.
1 November 2020 in International Journal of Advances in Engineering and Pure Sciences
In this study, Computational Fluid Dynamics (CFD) calculations are performed with ANSYS-Fluent for an external flow over a flat plate under constant surface temperature conditions. By using an Active Flow Control (AFC) method, the flat-plate is heated to manipulate the transition region. Calculations are performed for a steady and turbulent flow at 15 m/s free-stream velocity. Local skin friction coefficient and local heat transfer coefficient distributions along the flat-plate are investigated for laminar and turbulent boundary layers at various constant surface temperatures. For laminar and turbulent flow boundary layer characteristics, theoretical correlations in the literature are used to verify the numerical results. Results show that theoretical correlations are highly consistent with CFD results only in the laminar and turbulent regions and it is also shown that transition can only be predicted by CFD simulations. On the other hand, heating as an AFC method is found to be useful in delaying transition regime over a flat plate.