1 January 2020 in International Journal of Heat and Mass Transfer
1 January 2025 in Physics of Fluids
Reynolds Averaged Navier–Stokes turbulence models have been used over several decades in industrial and academic applications to predict turbulent flow fields. Adequacy of the predefined closure coefficients has received attention in the research community with increasing computational power in the last 20 years. In this study, the transitional and standard k–ω shear stress transport turbulence models are calibrated for flows over flat plate and backward facing step using six benchmark cases available in the literature. A systematical calibration methodology is presented, consisting of validation studies, global sensitivity analysis, reduced order modeling with Deep Neural Networks, and multi-objective optimization algorithm. Moreover, three different approaches are suggested to examine different aspects of the applicability of the calibrated closure coefficients. The results of the study demonstrate that the closure coefficients can be successfully calibrated using multi-objective optimization to improve the prediction of wall shear stresses and velocity profiles independent of the quantity of selected test cases. Comparison between different calibration approaches and their performance on different objective functions indicated their advantages and disadvantages. Calibrated values of the holistic calibration approach for the β1, β*, a1, b1, β2, and γ1 were found to be 6%, 25%, 24%, and 16% higher and 7% and 25% lower, respectively, than their default values.
27 September 2023 in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
This study aims to investigate the effects of irrigation needles geometries on the flow inside the root canal and compare their irrigation performances based on Computational Fluid Dynamics (CFD) analyzes. CFD simulations of three commonly used close-ended irrigation needles were performed for various inlet Reynolds numbers and working lengths. Their irrigation performances were evaluated based on apical pressure and wall shear stress. The flow was assumed to be incompressible, turbulent and steady at all inlet Reynolds numbers. The closed-ended needles showed similar limited irrigant penetration toward the apex. Among all configurations, the Model C outperforms others as it provides the highest wall shear stress around the needle tip and the lowest apical pressures in the apical foramen, which reduces the risk of apical extrusion. The needle tip designs influence important parameters for the effectiveness and safety of the irrigation process.
1 November 2020 in International Journal of Advances in Engineering and Pure Sciences
In this study, Computational Fluid Dynamics (CFD) calculations are performed with ANSYS-Fluent for an external flow over a flat plate under constant surface temperature conditions. By using an Active Flow Control (AFC) method, the flat-plate is heated to manipulate the transition region. Calculations are performed for a steady and turbulent flow at 15 m/s free-stream velocity. Local skin friction coefficient and local heat transfer coefficient distributions along the flat-plate are investigated for laminar and turbulent boundary layers at various constant surface temperatures. For laminar and turbulent flow boundary layer characteristics, theoretical correlations in the literature are used to verify the numerical results. Results show that theoretical correlations are highly consistent with CFD results only in the laminar and turbulent regions and it is also shown that transition can only be predicted by CFD simulations. On the other hand, heating as an AFC method is found to be useful in delaying transition regime over a flat plate.
20 June 2024 in Numerical Heat Transfer, Part B: Fundamentals
30 April 2023 in Isı Bilimi ve Tekniği Dergisi
In this study, convective heat transfer by multiple impinging jet arrays in different arrangements is numerically investigated using Computational Fluid Dynamics (CFD). Computational domain consists of multiple jet array either in inline or staggered alignment and a target plate to be cooled by impinging jets. Distance between the jet array and the target plate is kept constant at H=28 mm. Diameter of circular jet nozzles is fixed at D=5 mm for all configurations. Effects of jet Reynolds number (Rej), spacing between circular jets and the alignment of the jet nozzles on aerothermal performance are parametrically investigated in the scope of this study. For staggered and inline alignments of the jet nozzles, Rej ranges from 5000 to 20000 and the ratio of the spacing to the jet diameter (s/D) changes between 2 and 6. CFD calculations are performed using finite volume based ANSYS-Fluent flow solver. Simulations are conducted for incompressible, steady and turbulent flow using k-ω SST turbulence model with ideal gas assumption for density and Sutherland law for viscosity. After intensive mesh convergence and validation tests, appropriate mesh resolution is determined and parametric investigations are performed. The study reveals that most dominant parameter for plate cooling is Rej followed by spacing between jets and finally jet alignment. For all Rej, inline jet nozzle alignment provides 15% higher average heat transfer rate than staggered alignment when s/D is close to the lower limit. However, it is shown that jet alignment does not affect thermal performance when s/D is higher.