The shipping sector is required to give a significant contribution to the reduction of Green House Gas (GHG) emissions, according to the ambitious goals fixed by the International Maritime Organization (IMO). To achieve these targets, new technologies and measures are required, related to logistics, digitalization, hydrodynamics, machinery, energy, and aftertreatment. A large potential to reduce GHG emissions is offered by alternative fuels. In this perspective a Well-to-Wake (WtW) approach is due for a comprehensive analysis. The paper is focused on the evaluation of WtW CO₂ equivalent emission factors for LNG, methanol, and ammonia. The extensive bibliographic research on this topic outlines the large differences occurring when considering grey or green fuel production pathways. A case study based on a cruise ship allows to compare alternative fuels produced from fossil or renewable sources, considering two typical cruise profiles. Results in terms of Carbon Intensity Indicator confirms that the WtW approach points out the great potential of alternative green fuels for GHG emissions reduction.

The effect of rotational speed and pressure rise on the leakage flow noise radiated by a low-speed axial fan, provided with rotating shroud, has been systematically investigated. The flow in the gap region has been studied by means of particle image velocimetry (PIV) measurements taken in the meridional plane. At low blade loading, the leakage flow is restrained close to the rotor ring and, at higher loading, it forms a wide recirculation zone. In the latter conditions, an unsteady flow separation likely takes place in the blade tip region which may be observed in the instantaneous flow field only. The leakage flow noise generally increases with the blade loading, but is non-monotonic, as the overall sound pressure level (OASPL) growth is interrupted by local minima; such a trend is qualitatively independent of the rotational speed. As the loading increases, the sound pressure level (SPL) spectrum shows important modifications, since the characteristic frequency of the subharmonic narrowband humps related to the leakage noise decreases; furthermore, height and width of the humps vary non-monotonically. Such a complicated behavior is likely related to the modifications in the leakage flow pattern and also to the appearance of the flow separation at the blade tip.

The unsteady flow within a two-stage low-pressure research turbine equipped with high lift profiles has been investigated in detail for three different aerodynamic loading conditions. Experiments have been carried out at low speed. Velocity and turbulence intensity in the blade-to-blade plane at midspan have been measured by means of a crossed hot-wire probe, upstream and downstream of each blade row. The probe has been traversed circumferentially over 1.5 bladings pitch and the phase-locked data acquisition and ensemble average technique have been used to reconstruct the flow in space and time. The effects of multistage configuration have been identified and analyzed by considering the velocity components and turbulence intensity. Potential interaction from the downstream blading in relative motion, periodic wake perturbations from the upstream blading and preceding stage perturbations make the flow in the second stage extremely complex. Overall the flow downstream of rotors is perturbed in space by upstream and downstream stators, while flow downstream of stators is mostly perturbed in time by rotor effects. As expected, high lift profiles are significantly sensitive to incidence variation, with this effect further enhanced by the multistage cumulative interactions.

Lean premixing prevaporizing (LPP) burners represent a promising solution for low-emission combustion in aeroengines. Since lean premixed combustion suffers from pressure and heat release fluctuations that can be triggered by unsteady large-scale flow structures, a deep knowledge of flow structures formation mechanisms in complex swirling flows is a necessary step in suppressing combustion instabilities. The present paper describes a detailed investigation of the unsteady aerodynamics of a large-scale model of a double swirler aeroengine LPP burner at isothermal conditions. A three-dimensional (3D) laser Doppler velocimeter and an ensemble-averaging technique have been employed to obtain a detailed time-resolved description of the periodically perturbed flow field at the mixing duct exit and associated Reynolds stress and vorticity distributions. Results show a swirling annular jet with an extended region of reverse flow near to the axis. The flow is dominated by a strong periodic perturbation, which occurs in all the three components of velocity. Radial velocity fluctuations cause important periodic displacement of the jet and the inner separated region in the meridional plane. The flow, as expected, is highly turbulent. The periodic stress components have the same order of magnitude of the Reynolds stress components. As a consequence the flow-mixing process is highly enhanced. Turbulence acts on a large spectrum of fluctuation frequencies, whereas the large-scale motion influences the whole flow field in an ordered way that can be dangerous for stability in reactive conditions.

The continuous tendency in modern aeroengine gas turbines towards reduction of blade count and ducts length may lead to aerodynamic loading increase beyond the limit of boundary layer separation. For this reason boundary layer separation control methods, up to now mostly employed in external aerodynamics, begin to be experimented in internal flows applications. The present paper reports the results of a detailed experimental study on low profile vortex generators used to control boundary layer separation on a large-scale flat plate with prescribed adverse pressure gradients. Inlet turbulent boundary layer conditions and pressure gradients are representative of aggressive turbine intermediate ducts. This activity is part of a joint European research program on Aggressive Intermediate Duct Aerodynamics (AIDA). The pressure gradients on the flat plate are generated by increasing the aperture angle of a movable wall opposite to the flat plate. To avoid separation on the movable wall, boundary layer suction is applied on it. Complementary measurements (surface static pressure distributions, surface flow visualizations by means of wall mounted tufts, instantaneous and time-averaged velocity fields in the meridional and cross-stream planes by means of Particle Image Velocimetry) have been used to survey the flow with and without vortex generators. Three different pressure gradients, which induce turbulent separation in absence of boundary layer control, were tested. Vortex generators height and location effects on separation reduction and pressure recovery increase were investigated. For the most effective VGs configurations detailed analyses of the flow field were performed, that demonstrate the effectiveness of this passive control device to control separation in diffusing ducts. Particle Image Velocimetry vector and vorticity plots illustrate the mechanisms by which the vortex generators transfer momentum towards the surface, re-energizing the near-wall flow and preserving the boundary layer from separation.