This paper presents a 1.25-GS/s 7-b single-channel successive approximation register (SAR) analog-to-digital converter (ADC) that achieves a low input frequency SNDR/SFDR of 41.4/51 dB, while the SNDR/SFDR at Nyquist is 40.1/52 dB and remains still 36.4/50.1 dB at a 5-GHz input frequency (eighth Nyquist zone) without any calibration. The high and nearly constant linearity is enabled by an improved bootstrap circuit for the input switch, while the high sampling rate, the highest among recently published >34-dB SNDR single-channel SAR ADCs, is accomplished by a triple-tail dynamic comparator and a unit-switch-plus-cap (USPC) capacitive digital-to-analog converter (CDAC). To further enhance the ADC speed, the SAR logic operates in parallel to the comparator, eliminating its timing from the critical loop. The prototype chip in 28-nm bulk CMOS occupies a core area of 0.0071 mm² and consumes 3.56 mW from a 1-V supply, leading to a Walden figure-of-merit of 34.4 fJ/conversion-step at Nyquist.
7 January 2020 in IEEE Journal of Solid-State Circuits
This article presents a 5-GS/s 12-b passive-sampling 8x-interleaved hybrid analog-to-digital converter (ADC) that achieves a low-frequency SFDR/SNDR of 75.2/62.4 dB and a Nyquist SFDR/SNDR of 65.4/58.5 dB. A significant power reduction while attaining a bandwidth in excess of 6 GHz and a high spectral purity are enabled by: 1) an on-chip terminated very fast settling buffer-less input front end; 2) an on-chip clock chain with as low as 11-fs added jitter; 3) an asynchronous three-stage pipelined-successive approximation register (SAR) sub-ADC; and 4) on-chip co-designed analog-digital calibrations deal with sub-ADC and time-interleaving (TI) artifacts to achieve the desired spectral performance levels. The 28-nm bulk CMOS prototype chip occupies a total area of 4.56 mmsuperscript2 with a core area of 1.76 mmsuperscript2 and consumes 158.6 mW from a 1-V supply, leading to the Nyquist figure of merits of Schreier (FoMS) and Walden (FoMW) of 160.5 dB and 46.1 fJ/conversion step, respectively.
24 August 2022 in IEEE Transactions on Circuits and Systems I: Regular Papers
This article presents a fully dynamic latched comparator with a high-gain three-stage configuration and an extra parallel feed-forward path, able to achieve a delay of 26.8 ps and a data rate of 13.5 Gb/s with less than 10-12 BER for a 5 m $\text{V}_{\text{pp}}$ differential input ( $\Delta V_\textrm{I}$ ) at 0.5 V common-mode ( $V_\textrm{CM}$ ) and 1V supply ( $V_\textrm{DD}$ ). Additionally, the reduced-stacking cascaded triple-latch arrangement enables a $<$ 70ps delay down to 0.6 V $V_\textrm{DD}$ . The comparator is analyzed and compared against two prior art circuits by means of derived delay and noise expressions, serving as design guidelines. The prototype comparator and its prior art are fabricated in 28 nm bulk CMOS, with delay, input-referred noise, energy/comparison, and area measurements highlighting the benefits and trade-offs of the proposed solution.
1 September 2019 in IEEE Solid-State Circuits Letters
This article presents a data-compressive neural recording IC for single-cell resolution high-bandwidth brain–computer interfaces (BCIs). The IC features wired-OR lossy compression during digitization, thus preventing data deluge and massive data movement. By discarding unwanted baseline samples of the neural signals, the output data rate is reduced by 146$\times $ on average while allowing the reconstruction of spike samples. The recording array consists of pulse-position modulation (PPM)-based active digital pixels (ADPs) with a global single-slope (SS) analog-to-digital conversion scheme, which enables a low-power and compact pixel design with significantly simple routing and low array readout energy. Fabricated in a 28-nm CMOS process, the neural recording IC features 1024 channels (i.e., 32 $\times $ 32 array) with a pixel pitch of 36 $\mu \text{m}$ that can be directly matched to a high-density micro-electrode array (MEA). The pixel achieves 7.4-$\mu \text{V}_{\text {rms}}$ input-referred noise with a −3-dB bandwidth of 300 Hz–5 kHz while consuming only 268 nW from a single 1-V supply. The IC achieves the smallest area per channel (36 $\times $ 36 $\mu \text {m}^{{2}}$ ) and the highest energy efficiency among the state-of-the-art neural recording ICs published to date.
Emerging 5G communication systems require ADCs to directly digitize wide bandwidth (BW) signals with high spectral purity at low power consumption. Current state-of-the-art solutions include mainly time-interleaved (TI) pipelined [1-4] or pipelined-SAR [5] architectures, enhanced by digital calibration. To ensure a sufficiently high input BW, all these designs employ a static front-end buffer. This buffer often dissipates more power than the ADC itself, significantly deteriorates the linearity and noise performance, and severely limits the available swing, unless over-voltage or multiple supplies are used [1-5].