Optical methods such as ultraviolet/visible (UV/Vis) and fluorescence spectroscopy are well-established analytical techniques for in situ water quality monitoring. A broad range of bio-logical and chemical contaminants in different concentration ranges can be detected using these methods. The availability of results in real time allows a quick response to water quality changes. The measuring devices are configured as portable multi-parameter probes. However, their specification and data processing typically cannot be changed by users, or only with difficulties. Therefore, we developed a submersible sensor probe, which combines UV/Vis and fluorescence spectroscopy together with a flexible data processing platform. Due to its modular design in the hardware and software, the sensing system can be modified to the specific application. The dimension of the waterproof enclosure with a diameter of 100 mm permits also its application in groundwater monitoring wells. As a light source for fluorescence spectroscopy, we constructed an LED array that can be equipped with four different LEDs. A miniaturized deuterium–tungsten light source (200–1100 nm) was used for UV/Vis spectroscopy. A miniaturized spectrometer with a spectral range between 225 and 1000 nm permits the detection of complete spectra for both methods.
Usage of commercially available electrochemical gas sensors is currently limited by both the working range of the sensor with respect to temperature and humidity and the spikes in sensor response caused by sudden changes in temperature or humidity. Using a thermostatically controlled chamber, the sensor response of ammonia and hydrogen sulfide sensors was studied under extreme, rapidly changing levels of humidity with the aim of analyzing nebulized water samples. To protect the sensors from damage, the gas stream was alternated between a saturated gas stream from a Flow Blurring® nebulizer and a dry air stream. When switching between high and low humidity gas streams, the expected current spike was observed and mathematically described. Using this mathematical model, the signal response due to the change in humidity could be subtracted from the measured signal and the sensor response to the target molecule recorded. As the sensor response is determined by the model while the sensor is acclimatizing to the new humid conditions, a result is calculated faster than that by systems that rely on stable humidity. The use of the proposed mathematical model thus widens the scope of electrochemical gas sensors to include saturated gas streams, for example, from nebulized water samples, and gas streams with variable humidity.
Although condition monitoring is very important for a reliable operation of tram powertrain components, conventional wired sensor systems do not manage to find wide acceptance because of installation and security costs. To address those issues, we propose a novel condition monitoring system based on a wireless and energy self-sufficient sensor network, where the individual sensor nodes harvest energy from vibrations, occurring while the tram is in motion. First, we performed an experimental investigation to identify the most important boundary conditions for the system design. Second, we designed individual sensor nodes using parameters derived from the previous investigation. Finally, the sensor network was deployed and tested on the tram gearboxes. The obtained measurement data were recorded at a sufficient sampling rate of 4.56 kHz and were successfully transferred from the tram gearbox to the network base station within a radius of 10 m inside the tram despite factors such as reflections, fading and electromagnetic compatibility. A piezoelectric vibration harvester is the power supply for the sensor nodes and it delivers up to 21.22 mW for relevant vibration frequency range between 10 Hz and 30 Hz, thus enabling deployment of autonomous sensor nodes.
1 May 2022 in Zeitschrift für wirtschaftlichen Fabrikbetrieb
Die Auslastung des schienengebundenen ÖPNV wird durch Urbanisierung und energiepolitische Trends zunehmen. Für die dafür erforderliche Umsetzung einer zustandsabhängigen Instandhaltungsstrategie wurde ein innovatives schwingungsbasiertes Verfahren zur Zustandsdiagnose von Straßenbahnschienen entwickelt. Die klassifizierten Messdaten in Form von Gleismeterobjekten werden cloudbasiert in einer Kartenansicht zur Verfügung gestellt. Dadurch ist die Analyse historischer und aktueller Messdaten möglich, um die Notwendigkeit oder den Erfolg von Schienenschleifungen zu bewerten.
1 August 2021 in Zeitschrift für wirtschaftlichen Fabrikbetrieb
Durch die Möglichkeit, Wartungsintervalle dynamisch und zustandsabhängig planen zu können, gewinnen messdatengetriebene Instandhaltungskonzepte in modernen Fertigungslinien zunehmend an Bedeutung. Diese erlauben neben der Gewährleistung einer gleichbleibenden Prozessqualität die Schonung von Ressourcen. Bestehende Zustandsüberwachungen nutzen eine auf Kenn- und Grenzwerten basierende Messdatenauswertung. Alternativ dazu wird hier ein Verfahren der unscharfen Auswertung zur Prozessoptimierung an Werkzeugmaschinen vorgestellt, das keine Definition einzelner Grenzwerte erfordert, sondern basierend auf Methoden des maschinellen Lernens einen robusten Algorithmus zur Verfügung stellt, mit dem sich der Prozesszustand vorgegebenen Klassen zuordnen lässt. So lassen sich Unregelmäßigkeiten im Prozess anhand der Klassenzugehörigkeitswerte identifizieren und Diagnosefehler vermeiden.