Mateusz Kozioł

Dr. Mateusz Kozioł

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 July 2023 in Universe
Verified
Journal Article
Open access
PDF file
AAA. Alekou
A. Alekou
EBE. Baussan
E. Baussan
ABA. K. Bhattacharyya
A. K. Bhattacharyya
NKN. Blaskovic Kraljevic
N. Blaskovic Kraljevic
MBM. Blennow
M. Blennow
YZY. Zou
Y. Zou
ESSnuSB is a design study for an experiment to measure the CP violation in the leptonic sector at the second neutrino oscillation maximum using a neutrino beam driven by the uniquely powerful ESS linear accelerator. The reduced impact of systematic errors on sensitivity at the second maximum allows for a very precise measurement of the CP violating parameter. This review describes the fundamental advantages of measurement at the second maximum, the necessary upgrades to the ESS linac in order to produce a neutrino beam, the near and far detector complexes, and the expected physics reach of the proposed ESSnuSB experiment, concluding with the near future developments aimed at the project realization.

2 January 2020 in Mechanics Based Design of Structures and Machines
Verified
Journal Article
Closed access
MKMateusz Kozioł
Mateusz Kozioł
PCPiotr Cupiał
Piotr Cupiał
The article presents the results of the analysis of the active control of Stodola-Green rotor, made of a cantilevered beam with a rigid disc attached to its free end. The rotor is of a smart type, with piezoelectric patch sensors and actuators glued to its surface. The aim of active control is to decrease the effective internal damping, thus increasing the range of stable operation. The simulation studies show that it is feasible to increase the range of stability of rotors by means of velocity feedback control. Unlike in most studies that utilize this control scheme, negative gains are used, which allows for the effective internal damping to be decreased. Communicated by Francisco Javier González Varela.

1 September 2013 in Journal of Low Frequency Noise, Vibration and Active Control
Verified
Journal Article
Open access
PCPiotr Cupial
Piotr Cupial
MKMateusz Kozioł
Mateusz Kozioł
The paper discusses the analysis of the active control of a Jeffcott rotor with the rotational speed in the supercritical range. By the application of collocated sensors and actuators and a suitable control algorithm it has been possible to influence the internal damping of the rotor, which is the origin of self-induced vibrations. By this approach it is possible to increase the range of the stable operation of the rotor. In the paper, a classical analytical two-degree-of-freedom Jeffcott rotor model has been extended to account for the presence of piezoelectric patch sensors and actuators. The applicability of this model has been positively verified through the comparison with the finite element results derived using the Ansys software. Plots have been obtained by both the analytical approach and the finite element method that demonstrate the applicability of velocity feedback to increasing the threshold of instability of the rotor.

24 August 2026 in Materials
Verified
Journal Article
Open access
PDF file
Jolanta KrupaJolanta Krupa
Jolanta Krupa
JBJędrzej Blaut
Jędrzej Blaut
MWMariusz Warzecha
Mariusz Warzecha
MKMateusz Kozioł
Mateusz Kozioł
ŁBŁukasz Breńkacz
Łukasz Breńkacz
This paper presents the results of experimental studies on the mechanical and tribological properties of samples produced using the fused filament fabrication method. These studies aim to identify a potential material for a water-lubricated sliding bearing that will be manufactured using 3D printing. Printed specimens fabricated from four different materials were analyzed for surface profile, mechanical properties via the instrumented indentation method, and tribological behavior using a pin-on-disc setup. Although increased hardness is generally associated with improved resistance to wear, the material that exhibited the lowest wear in the pin-on-disc tests was characterized by the lowest hardness among all investigated materials. The findings suggest that other aspects, including wear mechanisms, wear products, and tribolayer development, may also exert a substantial influence.