In this paper, transmission phase-shift method was applied on free-space measurements for thin planar material characterization. The free-space measurement system consists of two pyramidal horn antennas, coaxial cables, network analyser, sliding guide, two antenna holders/stands, sample holder and two precision positioners. The free-space measurement system was operated in frequency range from 10 GHz to 15 GHz. The planar acrylic samples with different thicknesses were used for measurement validation. The relative permittivity of those samples were predicted from the measured reflection/transmission coefficients based on transmission phase shift concept. Before the actual measurement is done, systematic errors due to multiple reflections along the measurement distance between the horn antenna aperture and the planar sample surface were calibrated by using Thru-Reflect-Line (TRL) technique. In the free-space measurements, performance of the horn antenna and the distance between the two horn antennas played an important role in the measurement set-up. However, the mentioned measurement set-up factors were usually less discussed in previous literatures. Hence, in this study, these issues will be discussed in order to improve accuracy and reduce the multi-reflection in the measurement. Besides, the effect of thickness for the sample in permittivity prediction was also discussed and analysed in detail. Formerly, the thickness of the planar sample was not recommended to be more than a quarter of the wavelength in order to avoid phase-shift ambiguity problems and effects on the accuracy of the broadband relative permittivity prediction. Here, the phase-shift ambiguity issue due to the sample thickness was solved by the MATLAB command “unwrap” during the mathematical calculation of the permittivity value. In addition, this proposed method is sample position-invariant. Hence, the measurement errors due to the uncertainty of the sample position can be avoided.
This paper focuses on the non-destructive dielectric measurement for low-loss planar materials with a thickness of less than 3 mm using a large coaxial probe with an outer diameter of 48 mm. The aperture probe calibration procedure required only to make a measurement of the half-space air and three offset shorts. The reflection coefficient for the thin material is measured using a Keysight E5071C network analyzer from 0.3 MHz to 650 MHz and then converted to a relative dielectric constant, εr and tangent loss, tan δ via closed form capacitance model and lift-off calibration process. Average measurement error of dielectric constant, Δεr is less than 6% from 1 MHz to 400 MHz and the resolution of loss tangent, tan δ measurement is capable of achieving 10−3.
In this paper, a broadband metamaterial microwave absorber was designed and fabricated. Five unit cells of different geometrical dimensions which were designed using CST simulator, achieved at least 80% absorption of microwave at 11 GHz, 12 GHz, 13 GHz, 14 GHz and 15 GHz, respectively. The proposed metamaterial absorbers unit cell was composed of a split ring resonator and a microstrip slot structure, which was printed in repeated pattern on both sides of FR-4 substrate with 1.58 mm and (20×20) cm 2 of thickness and area, respectively. In this study, the designed microstrip slot structure contains multi-width section compared to a conventional linear slot structure. Parametric studies of the geometrical dimensions for the metamaterial absorber were observed and analysed. The size of the unit cell decreased by 7% in average which caused the shifting of absorption peak from lower to higher frequency by 1 GHz. The metamaterial absorbers were experimentally tested using free-space measurement technique covering X-Ku band in which the planar surface of the metamaterial absorber was normal to the incident wave (in-plane). The S-parameters measurement results showed that the absorption properties of the metamaterial for normal incidence case (in-plane) were slightly deviate from the simulation results by shifting 0.3 GHz to higher frequency.
1 June 2020 in Journal of Microwaves, Optoelectronics and Electromagnetic Applications
This paper investigates the dielectric properties and magnetic properties of epoxy composites with different amount of powdered iron phosphate glass (IPG) at 8.2 GHz to 12.4 GHz using microwave technique. IPG composed of 60P2O5-40Fe2O3 (mol%) was produced by conventional melt and quenching method and crushed into powder. The IPG powder was characterized using energy dispersive X-ray spectroscopy (EDS), particle size analyzer and powder X-ray diffraction (XRD). Different amount of IPG (10-70 wt%) were dispersed in the epoxy. The epoxy-IPG composites were characterized by their morphology, elemental composition and scattering parameters using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and vector network analyzer (VNA), respectively. Reflection coefficient, |S11| increases whereas transmission coefficient, |S21| decreases with increasing IPG content in epoxy. Dielectric constant, εr' of epoxy-IPG composites were found increased with the IPG content from 3.33 to 4.69.
This paper proposes a dual-band metamaterial microwave absorber operating at 2.5 GHz and 5.8 GHz. The absorber consists of a ring and a circular patch with slits resonator structures printed on a FR4 dielectric substrate backed by a ground layer. The main advantage of the absorber lies in its design flexibility in which each absorption band is independent and can be individually tuned by changing the dimensions of each resonator structure. The absorber unit cell is simulated and parametrically optimized using Computer Simulation Technology (CST) software. The absorption mechanism is analyzed through surface current analysis. The absorber prototype, with dimensions of 200 × 200 × 1.6 mm3 and consisting of an array of 7 × 7 unit cells, is fabricated and experimentally investigated using antennas in free-space measurement. The absorber exhibits over 97% absorption at both resonance frequencies. Furthermore, the absorber is demonstrated to be applicable in sensing applications for dielectric constant determination. With its design simplicity, wide-angle receptive, and polarization insensitive behavior, it is envisaged that the proposed absorber will find practical use in absorbing and sensing applications.