In this work, Sr0.3Ba0.4Pb0.3Fe12O19/(CuFe2O4)x (x = 2, 3, 4, and 5) as strongly exchange-coupled nanosized ferrites were fabricated using a one-pot sol–gel combustion method (citrate sol-gel method). The X-ray diffraction (XRD) powder patterns of the products confirmed the occurrence of pure, exchange-coupled ferrites. Frequency dependencies of the microwave characteristics (MW) were investigated using a co-axial method. The non-linear behavior of the MW with the composition transformation may be due to different degrees of Fe ion oxidation on the spinel/hexaferrite grain boundaries and strong exchange coupling during the hard and soft phases.
29 November 2015 in International Journal of Microwave Science and Technology
This paper describes a detailed study on the application of an open ended coaxial probe technique to determine the permittivity of in the frequency range between 1 GHz and 10 GHz. The compositions of the spinel ferrite were 0.1, 0.3, 0.5, 0.7, and 0.9. The samples were prepared by 10-hour sintering at 900°C with 4°C/min increment from room temperature. Particles showed phase purity and crystallinity in powder X-ray diffraction (XRD) analysis. Surface morphology measurement of scanning electron microscopy (SEM) was conducted on the plane surfaces of the molded samples which gave information about grain morphology, boundaries, and porosity. The tabulated grain size for all samples was in the range of 62 nm–175 nm. The complex permittivity of Ni-Zn ferrite samples was determined using the Agilent Dielectric Probe Kit 85070B. The probe assumed the samples were nonmagnetic homogeneous materials. The permittivity values also provide insights into the effect of the fractional composition of on the bulk permittivity values . Vector Network Analyzer 8720B (VNA) was connected via coaxial cable to the Agilent Dielectric Probe Kit 85070B.
30 April 2022 in Journal of Sustainability Science and Management
This paper investigates the dielectric properties and magnetic properties of epoxy composites with different amount of powdered iron phosphate glass (IPG) at 8.2 GHz to 12.4 GHz using microwave technique. IPG composed of 60P2O5-40Fe2O3 (mol%) was produced by conventional melt and quenching method and crushed into powder. The IPG powder was characterized using energy dispersive X-ray spectroscopy (EDS), particle size analyzer and powder X-ray diffraction (XRD). Different amount of IPG (10-70 wt%) were dispersed in the epoxy. The epoxy-IPG composites were characterized by their morphology, elemental composition and scattering parameters using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and vector network analyzer (VNA), respectively. Reflection coefficient, |S11| increases whereas transmission coefficient, |S21| decreases with increasing IPG content in epoxy. Dielectric constant, εr' of epoxy-IPG composites were found increased with the IPG content from 3.33 to 4.69.
Superconductivity in nanostructured ceramics offers significant advantages over the conventional coarse-grained materials in view of miniaturization of superconducting electronic devices. In this paper, we report the formation of four morphologies of superconducting YBa2Cu3O7-δ (YBCO) nanostructures by electrospinning technique using polymeric polyvinyl pyrrolidone (PVP) solutions of different molecular weight and altering the total content of the metallic precursors. The morphologies prepared using this strategy are nanorods (NRs), nanogarlands (NGs), nanohierarchical (NH), and nanoparticles (NPs). Alternating current susceptibility measurements showed high critical temperatures (TC ~90 K) for the NH YBCO synthesized using PVP of the lowest molecular weight; whereas the YBCO NRs synthesized using a higher molecular weight polymer showed the lowest TC (82 K). A relationship between the particulate properties and TC was also observed – the lower is the pore size the higher is the TC. The YBCO NGs showed the highest specific surface area (7.06 m2/g) with intermediate TC (88 K). Electrospinning process appears an effective and controllable technique to produce different nanomorphologies with intrinsic properties suitable for practical applications.