Stephen Buerger

Dr. Stephen Buerger

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2020 in IEEE Transactions on Robotics
Verified
Journal Article
Closed access
CHClinton G. Hobart
Clinton G. Hobart
AMAnirban Mazumdar
Anirban Mazumdar
SSSteven J. Spencer
Steven J. Spencer
MQMorgan Quigley
Morgan Quigley
JSJesper P. Smith
Jesper P. Smith
SBStephen Buerger
Stephen Buerger
Legged humanoid robots promise revolutionary mobility and effectiveness in environments built for humans. However, inefficient use of energy significantly limits their practical adoption. The humanoid biped walking anthropomorphic novelly-driven efficient robot for emergency response (WANDERER) achieves versatile, efficient mobility, and high endurance via novel drive-trains and passive joint mechanisms. Results of a test in which WANDERER walked for more than 4 h and covered 2.8 km on a treadmill, are presented. Results of laboratory experiments showing even more efficient walking are also presented and analyzed in this article. WANDERER's energetic performance and endurance are believed to exceed the prior literature in human-scale humanoid robots. This article describes WANDERER, the analytical methods and innovations that enable its design, and system-level energy efficiency results.

1 January 2010 in AIP Conference Proceedings
Verified
Conference Paper
Open access
MRM. E. Riesco
M. E. Riesco
CMC. H. McLean
C. H. McLean
GMG. L. Mills
G. L. Mills
SBStephen Buerger
Stephen Buerger
MMM. L. Meyer
M. L. Meyer
JWJ. G. Weisend
J. G. Weisend
The NASA Exploration Program is currently studying the use liquid oxygen, liquid methane and liquid hydrogen for propulsion in future spacecraft for Exploration of the Moon and Mars. This will require the efficient long term, on‐orbit storage of these cryogenic propellants. Multilayer Insulation (MLI) will be critical to achieving the required thermal performance since it has much lower heat transfer than any other insulation when used in a vacuum. MLI with a low density (⩽10 layers/cm) has been shown in previous work to be the most mass efficient. The size and mass constraints of these propulsion systems will not allow a structural shell to be used to provide vacuum for the MLI during ground hold and launch. The baseline approach is to purge the MLI during ground hold with an inert gas which is then vented during launch ascent and on‐orbit. This paper presents the results on experimental tests and modeling performed by Ball Aerospace on low density, non‐perforated MLI used to insulate a cryogenic tank simulating an Exploration cryogenic propellant storage vessel. These include measurements of the rate of venting and of the heat transfer of gas filled insulation, fully evacuated insulation and during the transition in between. Results of transient computer modeling of the MLI venting and heat transfer process are also presented. Previous work by some of the authors performed vent testing using MLI with perforations and slits and a slow pump down rate.

1 May 2007
Verified
Conference Paper
Closed access
SBStephen Buerger
Stephen Buerger
RORoy H. Olsson
Roy H. Olsson
KWKenneth E. Wojciechowski
Kenneth E. Wojciechowski
EYEsteban Yepez
Esteban Yepez
DNDavid Novick
David Novick
DKDeepesh K. Kholwadwala
Deepesh K. Kholwadwala
While existing work in neural interfaces is largely geared toward the restoration of lost function in amputees or victims of neurological injuries, similar technology may also facilitate augmentation of healthy subjects. One example is the potential to learn a new, unnatural sense through a neural interface. The use of neural interfaces in healthy subjects would require an even greater level of safety and convenience than in disabled subjects, including reliable, robust bidirectional implants with highly-portable components outside the skin. We present our progress to date in the development of a bidirectional neural interface system intended for completely untethered use. The system consists of a wireless stimulating and recording peripheral nerve implant powered by a rechargeable battery, and a wearable package that communicates wirelessly both with the implant and with a computer or a network of independent sensor nodes. Once validated, such a system could permit the exploration of increasingly realistic use of neural interfaces both for restoration and for augmentation.

1 October 2024
Verified
Report
Open access
PDF file
A(Albuquerque Sandia National Laboratories (Snl-Nm)
Albuquerque Sandia National Laboratories (Snl-Nm)
DMDaniel R. McArthur
Daniel R. McArthur
U(Usdoe National Nuclear Security Administration (Nnsa)
Usdoe National Nuclear Security Administration (Nnsa)
JSJonathon Slightam
Jonathon Slightam
SSSteven James Spencer
Steven James Spencer
SBStephen Buerger
Stephen Buerger
3-minute Powerpoint presentation of conference paper content

22 October 2026 in Robotics
Verified
Journal Article
Open access
PDF file
DMDaniel R. McArthur
Daniel R. McArthur
DTDerya Tansel
Derya Tansel
CHClint Hobart
Clint Hobart
JOJosh Ortiz
Josh Ortiz
SBStephen Buerger
Stephen Buerger
This paper presents the design of SPIINE, a compliant six-wheeled robot for in-pipe inspection with geometry constraints. SPIINE, the Self-Propelled Interior Inspector for Non-destructive-testing (NDT) Examination, is designed to navigate 53 mm (2 in) inner-diameter pipes with tight 90° elbows, including elbows with a curvature radius as small as 76 mm (3 in), while transmitting power and high-resolution video over long tethers verified to 110 m. In straight steel pipe, SPIINE can generate more than eight times its weight in pull force to support towing of NDT sensor payloads. We also present analytical models for estimating robot stiffness and normal-force generation along with prototype hardware tests that evaluate model accuracy. Across the tested displacement range, the vertical reaction-force model achieved a root-mean-square error of 0.21 N; for two tested pipe configurations, pull-force estimates were within 7–13% of the measured values. Hardware experiments demonstrate that SPIINE can traverse a tight 90° elbow in forward and reverse at eight tested entry roll orientations spanning 360°, generate 16.5 N of pull force in straight steel pipe, and traverse more than 60 m of mixed horizontal and vertical pipe with low measured power consumption of approximately 2–3.5 W across representative test segments.

1 March 2025
Verified
Report
Closed access
PDF file
A(Albuquerque Sandia National Laboratories (Snl-Nm)
Albuquerque Sandia National Laboratories (Snl-Nm)
JWJason W. Wheeler
Jason W. Wheeler
SSSecurity And Quality Programs Safety
Security And Quality Programs Safety
MRMichal Rittikaidachar
Michal Rittikaidachar
NWNicholas Albert Wyatt Wright
Nicholas Albert Wyatt Wright
SBStephen Buerger
Stephen Buerger