Background: Relaxation methods determine residual stresses by measuring the deformations produced by incremental removal of a subdomain of the specimen. Measured strains at any given increment, determined by the cumulative effect of the relieved stresses, appear as an integral equation, which must be inverted to obtain residual stresses. In practice, stress distributions are discretized by a finite-dimensional basis, to transform the integral equations into a linear system of equations, which is often ill-conditioned.Objective: This article demonstrates that the problem is actually ill-posed and comes with an inherent bias-variance tradeoff.Methods: The hole drilling method is used as an example application, and the practical effects of ill-posedness are illustrated.Results: Traditional regularization of the solution by limiting the resolution of the discretization reduces solution variance (noise) at the expense of increased bias and often results in the ultimately harmful practice of taking fewer data points. A careful analysis including the alternate Tikhonov regularization approach shows that the highest number of measurements should always be taken to reduce the variance for a given regularization scheme. Unfortunately, the variability of a regularized solution cannot be used to build a valid confidence interval, since an unknown bias term is always present in the true overall error.Conclusions: The mathematical theory of ill-posed problems provides tools to manage the bias-variance tradeoff on a reasonable statistical basis, especially when the statistical properties of measurement errors are known. In the long run, physical arguments that provide constraints on the true solution would be of utmost importance, as they could regularize the problem without introducing an otherwise unknown bias. Constraining the minimum length scale to some physically meaningful value is one promising possibility.
Background: In a previous work, the problem of identifying residual stresses through relaxation methods was demonstrated to be mathematically ill-posed. In practice, it means that the solution process is affected by a bias-variance tradeoff, where some theoretically uncomputable bias has to be introduced in order to obtain a solution with a manageable signal-to-noise ratio. Objective: As a consequence, an important question arises: how can the solution uncertainty be quantified if a part of it is inaccessible? Additional physical knowledge could—in theory—provide a characterization of bias, but this process is practically impossible with presently available techniques. Methods: A brief review of biases in established methods is provided, showing that ruling them out would require a piece of knowledge that is never available in practice. Then, the concept of average stresses over a distance is introduced, and it is shown that finding them generates a well-posed problem. A numerical example illustrates the theoretical discussion Results: Since finding average stresses is a well-posed problem, the bias-variance tradeoff disappears. The uncertainties of the results can be estimated with the usual methods, and exact confidence intervals can be obtained. Conclusions: On a broader scope, we argue that residual stresses and relaxation methods expose the limits of the concept of point-wise stress values, which instead works almost flawlessly when a natural unstressed state can be assumed, as in classical continuum mechanics (for instance, in the theory of elasticity). As a consequence, we are forced to focus on the effects of stress rather than on its point-wise evaluation.
By means of relaxation methods, residual stresses can be obtained by introducing a progressive cut or a hole in a specimen and by measuring and elaborating the strains or displacements that are consequently produced. If the cut can be considered a controlled crack-like defect, by leveraging Bueckner’s superposition principle, the relaxed strains can be modeled through a weighted integral of the residual stress relieved by the cut. To evaluate residual stresses, an integral equation must be solved. From a practical point of view, the solution is usually based on a discretization technique that transforms the integral equation into a linear system of algebraic equations, whose solutions can be easily obtained, at least from a computational point of view. However, the linear system is often significantly ill-conditioned. In this paper, it is shown that its ill-conditioning is actually a consequence of a much deeper property of the underlying integral equation, which is reflected also in the discretized setting. In fact, the original problem is ill-posed. The ill-posedness is anything but a mathematical sophistry; indeed, it profoundly affects the properties of the discretized system too. In particular, it induces the so-called bias–variance tradeoff, a property that affects many experimental procedures, in which the analyst is forced to introduce some bias in order to obtain a solution that is not overwhelmed by measurement noise. In turn, unless it is backed up by sound and reasonable physical assumptions on some properties of the solution, the introduced bias is potentially infinite and impairs every uncertainty quantification technique. To support these topics, an illustrative numerical example using the crack compliance (also known as slitting) method is presented. The availability of the Linear Elastic Fracture Mechanics Weight Function for the problem allows for a completely analytical formulation of the original integral equation by which bias due to the numerical approximation of the physical model is prevented.
11 April 2024 in Journal of Materials Engineering and Performance