In this work, the quality of coatings prepared by plasma electrolytic oxidation (PEO) on an AZ31 magnesium alloy were evaluated. This was done by studying the effects of the chemical composition of phosphate-based process electrolytes in combination with different applied current densities on coating thickness, porosity, micro-cracking and corrosion resistance in 0.1 M NaCl. Both processing parameters were studied in four different levels. Mid-term corrosion resistance in 0.1 M NaCl was examined by electrochemical impedance spectroscopy and based on this, corrosion mechanisms were hypothesized. Results of performed experiments showed that the chosen processing parameters and electrolyte composition significantly influenced the morphology and corrosion performance of the prepared PEO coatings. The PEO coating prepared in an electrolyte with 12 g/L Na₃PO₄·12H₂O and using an applied current density 0.05 A/cm² reached the highest value of polarization resistance. This was more than 11 times higher when compared to the uncoated counterpart.

Phosphorus-containing heterocyclic cationic surfactants alkyldimethylphenylphospholium bromides with the alkyl chain length 14 to 18 carbon atoms were used for the stabilization of silver nanodispersions. Zeta potential of silver nanodispersions ranges from +35 to +70 mV, which indicates the formation of stable silver nanoparticles (AgNPs). Long-chain heptadecyl and octadecyl homologs of the surfactants series provided the most intensive stabilizing effect to AgNPs, resulting in high positive zeta potential values and smaller diameter of AgNPs in the range 50–60 nm. A comparison with non-heterocyclic alkyltrimethylphosphonium surfactants of the same alkyl chain length showed better stability and more positive zeta potential values for silver nanodispersions stabilized with heterocyclic phospholium surfactants. Investigations of biological activity of phospholium-capped AgNPs are represented by the studies of antimicrobial activity and cytotoxicity. While cytotoxicity results revealed an increased level of HepG2 cell growth inhibition as compared with the cytotoxicity level of silver-free surfactant solutions, no enhanced antimicrobial action of phospholium-capped AgNPs against microbial pathogens was observed. The comparison of cytotoxicity of AgNPs stabilized with various non-heterocyclic ammonium and phosphonium surfactants shows that AgNPs capped with heterocyclic alkyldimethylphenylphospholium and non-heterocyclic triphenyl-substituted phosphonium surfactants have the highest cytotoxicity among silver nanodispersions stabilized by the series of ammonium and phosphonium surfactants.

The influence on the bond between the steel fiber and the matrix of the anticorrosive treatments of steel used for concrete reinforcement is not yet fully understood. The topic of steel fiber treatment was not also studied clearly in terms of brass removal before. This paper deals with how the brass on the surface of steel fibers behaves in the UHPC matrix and how it affects its properties. The steel fibers were firstly modified with a number of surface treatments to remove brass on their surface. Some of the treatments have never been tried before for this purpose. Secondly, the surface of the fibers was analyzed by SEM, EDS, XRF, and stereomicroscopy. Lastly, the properties of the composites were analyzed. It was found out that the majority of brass on the surface of the fibers could be removed by mixture of NH₃ and H₂O₂ with a ratio of 3:1 (v/v). It was also found out that the surface treatment slightly affects the mechanical properties, but it does that only by mechanical interlocking between the fiber and the matrix. No dissolution of the surface treatment was observed under the given conditions. According to the results, steel fibers without surface treatment should be used in UHPC if available.

An Fe-based coating was thermally sprayed onto the surface of AZ91 magnesium alloy via the High-Velocity-Oxygen-Fuel (HVOF) method. The thermally sprayed coating with a thickness of 530 ± 25 µm and a porosity of 0.7 ± 0.1% did not show any macrostructural defects and did not cause any degradation of the AZ91 alloy. Laser remelting of the surface layer of the sprayed coating resulted in the recrystallization of the structure and the disappearance of presented pores, splat boundaries, and other defects. This led to an increase in the hardness of the remelted layer from the original 535 ± 20 HV0.3 up to 625 ± 5 HV0.3. However, during the laser remelting at a laser power of 1000 W, stress cracking in the coating occurred. The tribological properties were evaluated by the ball-on-plate method under dry conditions. Compared to the uncoated AZ91 magnesium alloy, a higher value of friction coefficient (COF) was measured for the as-sprayed coating. However, there was a decrease in wear rate and weight loss. The remelting of the surface layer of the as-sprayed coating led to a further decrease in the wear rate and weight loss. Based on the obtained data, it has been shown that the application of laser-remelted thermally sprayed Fe-based coatings on AZ91 Mg alloy improves hardness and tribological properties compared to bare Mg alloy and as-sprayed Fe-based coatings.

Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, the scientific journal of the Mendel University in Brno, Czech Republic