Marco Ciaccia-Sortino, PhD Ciaccia Sortino

Prof. Marco Ciaccia-Sortino, PhD Ciaccia Sortino


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 July 2020
Verified
Book Chapter
Closed access
PDF file
MSMarco Ciaccia-Sortino, PhD Ciaccia Sortino
Marco Ciaccia-Sortino, PhD Ciaccia Sortino
CMCosme Mejia-Echeverria
Cosme Mejia-Echeverria
CVChristian Vásquez
Christian Vásquez
TAThalia San Antonio
Thalia San Antonio

1 October 2017
Verified
Conference Paper
Closed access
LPL. Pasaguayo
L. Pasaguayo
MSMarco Ciaccia-Sortino, PhD Ciaccia Sortino
Marco Ciaccia-Sortino, PhD Ciaccia Sortino
In this work, the improvement of a knee mechanism prosthesis is presented. The mechanism is oversized and has an excessive weight to load ratio. The excess weight causes discomfort and an increase in the consumption of metabolic energy of the prosthesis user. To improve the mechanism, a validation of the finite element model of the original device was performed through non-destructive experimental tests. The experimental loads ranged from the weight of a 65-kilogram user to the maximum load of the main structural test of the ISO 10328 standard. Strain gages were installed on the prototype and connected to a system of acquisition, filtering, and amplification of signals, designed, and constructed for this purpose, with which the device strains were measured. Then, the model was simulated with the experimental loads, and the maximum difference found between the experimental and numerical results was 12.43 %; therefore, the model was considered validated. Afterwards, geometric modifications were made to the model and the new simulations to the improved model resulted in a better distribution of the safety factor, a decrease of the safety factors up to 97 % and of the weight up to 43 %, maintaining its structural integrity.

3 March 2020
Verified
Book Chapter
Closed access
PDF file
BGBrizeida Nohemi Gamez
Brizeida Nohemi Gamez
DODavid Ojeda
David Ojeda
MSMarco Ciaccia-Sortino, PhD Ciaccia Sortino
Marco Ciaccia-Sortino, PhD Ciaccia Sortino
IIIván Iglesias-Navarro
Iván Iglesias-Navarro


29 June 2021 in INGENIUS
Verified
Journal Article
Open access
PDF file
GAGennifer Aparicio-Carrillo
Gennifer Aparicio-Carrillo
MSMarco Ciaccia-Sortino, PhD Ciaccia Sortino
Marco Ciaccia-Sortino, PhD Ciaccia Sortino
RGRicardo Jerez G.
Ricardo Jerez G.
The aluminum alloy AA3003 produced by a direct chill continuous casting process has a microstructure that significantly affects its potential use in engineering applications. This work studies the effects of the homogenizing heat treatment on the microstructure of AA3003 with cold working. Six conditions were studied, combining the variables initial condition (with and without homogenizing) and amount of cold working. All conditions were evaluated by means of optical and scanning electron microscopy, in combination with backscattered electrons and energy dispersive X ray spectroscopy techniques. Results suggest that for both initial conditions, the secondary phases present are Al6(Mn,Fe) and α-Al(Mn,Fe)Si, which vary in number, size, and shape. The homogenization caused the dissolution and precipitation of dispersoids, in addition to the spheroidization of primary particles, and minor variation of the size of secondary particles during cold working. Secondary phases are composed of primary and secondary particles, which differ in their Fe and Mn content, resulting in a lower Mn/Fe ratio for the primary particles (0,57 for the as‑received condition and 0,80 for the homogenized condition), whereas the dispersoids have a higher Mn/Fe ratio (1,56 after the homogenization). Homogenization increased ductility and reduced the likelihood of cracking during cold working. This was evidenced by the results obtained for strength, hardness, and ductility. La aleación de aluminio AA3003 proveniente de colada continua posee una microestructura que afecta significativamente su uso potencial en aplicaciones de ingeniería. Este trabajo estudia los efectos de la homogeneización sobre la microestructura del AA3003 con trabajo en frío. Se estudiaron seis condiciones combinando las variables: condición inicial (con y sin homogeneizado) y cantidad de trabajo en frío. Se evaluaron todas las condiciones mediante microscopía óptica y electrónica de barrido, combinadas con técnicas de electrones retrodispersados y espectroscopía de dispersión de rayos X. Los resultados sugieren que, para ambas condiciones iniciales, las fases secundarias presentes son Al6(Mn,Fe) y α-Al(Mn,Fe)Si. La homogeneización causó la disolución y precipitación de los dispersoides, la esferoidización de las partículas primarias y permitió que la variación del tamaño de las partículas secundarias fuese mínima durante el trabajo en frío. Además, se obtuvo que las fases secundarias están compuestas de partículas primarias y secundarias, que difieren en su contenido de Fe y Mn, lo que resulta en una relación Mn/Fe más baja para las partículas primarias (0,57 para la condición recibida y 0,80 para la condición homogeneizada), mientras que los dispersoides tienen una mayor relación Mn/Fe (1,56 después de la homogeneización). La homogenización aumentó la ductilidad y redujo la probabilidad de agrietamiento del material durante el trabajo en frío, lo cual se evidenció en los resultados obtenidos de resistencia, dureza y ductilidad.

29 June 2021 in INGENIUS
Verified
Journal Article
Open access
PDF file
GAGennifer Aparicio-Carrillo
Gennifer Aparicio-Carrillo
MSMarco Ciaccia-Sortino, PhD Ciaccia Sortino
Marco Ciaccia-Sortino, PhD Ciaccia Sortino
RGRicardo Jerez G.
Ricardo Jerez G.
The aluminum alloy AA3003 produced by a direct chill continuous casting process has a microstructure that significantly affects its potential use in engineering applications. This work studies the effects of the homogenizing heat treatment on the microstructure of AA3003 with cold working. Six conditions were studied, combining the variables initial condition (with and without homogenizing) and amount of cold working. All conditions were evaluated by means of optical and scanning electron microscopy, in combination with backscattered electrons and energy dispersive X ray spectroscopy techniques. Results suggest that for both initial conditions, the secondary phases present are Al6(Mn,Fe) and α-Al(Mn,Fe)Si, which vary in number, size, and shape. The homogenization caused the dissolution and precipitation of dispersoids, in addition to the spheroidization of primary particles, and minor variation of the size of secondary particles during cold working. Secondary phases are composed of primary and secondary particles, which differ in their Fe and Mn content, resulting in a lower Mn/Fe ratio for the primary particles (0,57 for the as‑received condition and 0,80 for the homogenized condition), whereas the dispersoids have a higher Mn/Fe ratio (1,56 after the homogenization). Homogenization increased ductility and reduced the likelihood of cracking during cold working. This was evidenced by the results obtained for strength, hardness, and ductility.