Due to weak physical properties of sand, chemical reinforcement methods are widely used to improve sand properties to meet the engineering requirements. However, most of the traditional additives cause environmental problems. Therefore, non-traditional additives such as liquid polymers, enzymes, ions, and lignin derivatives have been studied extensively. In this study, organic polymer is used as a soil stabilizer to reinforce the sand. To evaluate the effectiveness of the organic polymer as soil stabilizer, a series of unconfined compression strength (UCS) tests, direct shear tests, and tensile tests were carried out on reinforced sand with different polymer concentrations and dry densities of sand. The reinforcement mechanism was analysed with scanning electron microscopy (SEM) images. The results indicated that the polymer concentration and dry density of sand had significant effects on the strength characteristics of reinforced sand specimens. The unconfined compressive strength, cohesion, and tensile strength of specimens with the same dry density increased with the increasing polymer concentration. The polymer membranes—formed by the mixture of polymer and water—enwrap the sand particles and interlink them to form a stable structure. The efficiency of this stabilization changed with dry sand density.

Deformation monitoring is a powerful tool to understand the formation mechanism of earth fissure hazards, enabling the engineering and planning efforts to be more effective. To assess the evolution characteristics of the Yangshuli earth fissure hazard more completely, terrestrial laser scanning (TLS), a remote sensing technique which is regarded as one of the most promising surveying technologies in geohazard monitoring, was employed to detect the changes to ground surfaces and buildings in small- and large-scales, respectively. Time-series of high-density point clouds were collected through 5 sequential scans from 2014 to 2017 and then pre-processing was performed to filter the noise data of point clouds. A tiny deformation was observed on both the scarp and the walls, based on the local displacement analysis. The relative height differences between the two sides of the scarp increase slowly from 0.169 m to 0.178 m, while no obvious inclining (the maximum tilt reaches just to 0.0023) happens on the two walls, based on tilt measurement. Meanwhile, global displacement analysis indicates that the overall settlement slowly increases for the ground surface, but the regions in the left side of scarp are characterized by a relatively larger vertical displacement than the right. Furthermore, the comparisons of monitoring results on the same measuring line are discussed in this study and TLS monitoring results have an acceptable consistency with the global positioning system (GPS) measurements. The case study shows that the TLS technique can provide an adequate solution in deformation monitoring of earth fissure hazards, with high effectiveness and applicability.

The development height and settlement prediction of water-conducting fracture zones caused by coal seam mining play an important role in the stability of overburden aquifers and the safety of roadways. Based on the engineering geological data of the J60 borehole in the Daliuta Coal Mine and the mining conditions of the 2⁻² coal seam, China, this study established a similar material test model of mining overburden. The deformation characteristics of overlying strata in the mining process of coal seam were studied by using distributed optical fiber sensing technology, and the development height of water flowing fractured zone was determined. According to the equidistant sampling characteristics of Brillouin optical time domain reflection technology and the principle of the grey theory model, the settlement prediction model of the water-conducting fracture zone was established. By analyzing and comparing the prediction accuracy of the GM (1, 1) model, grey progressive model, and metabolic model, the optimal method for settlement prediction of the water-conducting fracture zone was discussed. The results show that, for the metabolic model, with the increase in the number of test sets and the decrease in the number of prediction sets, the mean square error ratio c and the small error probability p of the prediction accuracy evaluation parameters display a downward trend. The accuracy is related to the sudden change in the settlement of the water-conducting fracture zone caused by the breaking of the key stratum of the overlying rock. The optimal time of test sets selected for the best settlement prediction model is 7~8, and that of prediction sets selected is 5~6. For the GM (1, 1) model and the grey progressive model, the prediction accuracy of mining overburden subsidence is grade 4, which is not suitable for settlement prediction of water-flowing fractured zones.

The mechanical properties of sandy soil can be effectively improved by the incorporation of water-based polymer and glass fibers. In order to study the reinforcement effects of a type of water-based organic polymer and fiber glass on sand, three strength tests (unconfined compression test, direct shear test and tensile test) and scanning electron microscopy were carried out. A series of polymer content, fiber content and dry density were selected for the tests. The results revealed that the composite reinforcement of water-based organic polymer and fiber glass can improve the strength. With an increase in polymer content and fiber content, the unconfined compression strength, the cohesion, and the tensile strength increase. The internal friction angles maintain a relatively stable state. All three strength properties increase with an increase in dry density. The results can be considered as the reference for sand reinforced engineering.