Zhiwei Feng

Zhiwei Feng


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 February 2014 in Structural and Multidisciplinary Optimization
Verified
Journal Article
Closed access
PDF file
ZFZhiwei Feng
Zhiwei Feng
ZQZhang Qing-bin
Zhang Qing-bin
QTQiangang Tang
Qiangang Tang
TYTao Yang
Tao Yang
JGJianquan Ge
Jianquan Ge

8 May 2019 in IEEE Access
Verified
Journal Article
Open access
ZBZhang Bin
Zhang Bin
ZFZhiwei Feng
Zhiwei Feng
BXBoting Xu
Boting Xu
TYTao Yang
Tao Yang
The aerodynamic shape of the hypersonic glide vehicle (HGV) has become a research topic nowadays due to its excellent aerodynamic performances. Some limitations need to be reduced when the free-form deformation (FFD) method is applied to parametric modeling and design of an HGV. In this paper, a typical lifting body is considered as an example, and we propose a border-based FFD modeling method that transforms the boundary of FFD lattice into the border of the windward side. Then, the superiority of the border-based FFD modeling method is demonstrated by comparison with the traditional FFD modeling method, and the mesh quality parameters are used to validate the well-deformed model and good geometric continuity of the proposed method. Finally, the border-based FFD modeling method is applied to deformable modeling and aerodynamic simulation of three typical HGV shapes. The results show that the higher efficiency, wider design space, and better applicability are performed by using the border-based FFD modeling method that outperforms the traditional FFD modeling method, and this method we proposed can allow a designer to achieve the better aerodynamic shape of HGVs.

2 September 2022 in Engineering Optimization
Verified
Journal Article
Closed access
HHHao Huang
Hao Huang
ZFZhiwei Feng
Zhiwei Feng
LMLikun Ma
Likun Ma
TYTao Yang
Tao Yang
QZQingbin Zhang
Qingbin Zhang
JGJianquan Ge
Jianquan Ge
Computationally expensive constrained optimization problems are challenging owing to their high complexity and computational cost. To solve these problems efficiently, a kriging-assisted bi-objective constrained global optimization (BOCGO) algorithm is developed, where three phases with three bi-objective subproblems are performed. In phase I, the constraints are searched locally and globally to find the feasible region. Once a feasible region has been located, the two terms of the constrained expected improvement function are utilized to exploit and explore the feasible region in phase II. As the kriging models are accurate enough in the concerned region, a local search is processed to improve the optimal solution in phase III. The capability of the BOCGO algorithm is demonstrated by comparison with two classical and two state-of-the-art algorithms on 20 problems and an engineering simulation problem. The results show that the BOCGO algorithm performs better in more than three-fifths of problems, illustrating its effectiveness and robustness.

28 October 2021 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Verified
Journal Article
Closed access
PDF file
HHHao Huang
Hao Huang
ZFZhiwei Feng
Zhiwei Feng
LMLikun Ma
Likun Ma
TYTao Yang
Tao Yang
CLChaolong Li
Chaolong Li
Combustion efficiency is the main factor affecting the performance of solid fuel rocket scramjet. To reveal the influence of combustor configuration on performance and further improve combustion efficiency, the influence of the width-height ratio of the rectangle-section combustor on the performance of solid fuel rocket scramjet is investigated numerically in this article. Three-dimensional compressible Reynolds-averaged Navier-Stokes equations coupled with shear stress transport k–ω turbulence model are employed to simulate the aerodynamics. The Euler–Lagrange approach is used to calculate the multiphase flow. Combustion of carbon particles is modeled by the improved Moving Flame Front model. Accuracy of the present numerical model is validated by the experimental data of a rectangle-section combustor from literature. Results show that as the width-height ratio increases, the combustion efficiency increases first and then decreases. The influence of cavity and its position on the performance are also investigated. Results show that cavity can significantly improve combustion efficiency. The effect of cavity position on performance is related to the distribution of particles.

1 March 2020 in Advances In Space Research
Verified
Journal Article
Closed access
ZQZhang Qing-bin
Zhang Qing-bin
ZFZhiwei Feng
Zhiwei Feng
MZMengying Zhang
Mengying Zhang
QCQingquan Chen
Qingquan Chen

25 July 2018 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Verified
Journal Article
Closed access
ZBZhang Bin
Zhang Bin
ZFZhiwei Feng
Zhiwei Feng
TYTao Yang
Tao Yang
BXBoting Xu
Boting Xu
XSXiaojian Sun
Xiaojian Sun
Highly robust mesh deformation methods are key techniques for solving unsteady flow field problems with moving or deforming boundaries. Because it is imperative to reduce the remeshing times, these methods are important in engineering applications, especially for complex geometric boundaries and large displacements. We introduce three classical elasticity-based mesh deformation methods and determine the limitations of the two nonlinear classical methods. Two steps were taken to achieve an integrated improvement: first, the robust power parameters a and b and the weighted parameter x are introduced to enhance the robustness of the basic elasticity equation. Second, a mesh quality parameter is implemented to prevent the large distortion of the poor elements and this parameter is added to the elasticity equation as a constraint. To validate the validity of the integrated improvement approach, several test cases of a moving or deforming two-dimensional flat plate are used. Additionally, two simulated engineering examples are used to demonstrate the application of the integrated improvement for practical problems, including the pitching oscillation of a National Advisory Committee for Aeronautics (NACA) 0012 airfoil and the ONERA M6 wing. The results show that the integrated improvement approach does not only allow for the selection of suitable robust parameters to achieve more robust deformed meshes but also reduces the distortion of the poor elements near the moving boundary, even when the deformation is severe.