Scramjet based on solid propellant is a good supplement for the power device of future hypersonic vehicles. A new scramjet combustor configuration using solid fuel, namely, the solid fuel rocket scramjet (SFRSCRJ) combustor is proposed. The numerical study was conducted to simulate a flight environment of Mach 6 at a 25 km altitude. Three-dimensional Reynolds-averaged Navier–Stokes equations coupled with shear stress transport (SST) turbulence model are used to analyze the effects of the cavity and its position on the combustor. The feasibility of the SFRSCRJ combustor with cavity is demonstrated based on the validation of the numerical method. Results show that the scramjet combustor configuration with a backward-facing step can resist high pressure generated by the combustion in the supersonic combustor. The total combustion efficiency of the SFRSCRJ combustor mainly depends on the combustion of particles in the fuel-rich gas. A proper combustion organization can promote particle combustion and improve the total combustion efficiency. Among the four configurations considered, the combustion efficiency of the mid-cavity configuration is the highest, up to about 70%. Therefore, the cavity can effectively increase the combustion efficiency of the SFRSCRJ combustor.
Considering the dynamic RCS characteristics of stealthy UAVs, we proposed a stealthy UAV path planning algorithm based on the Double Deep Q-Network (DDQN). By introducing the reinforcement learning model that can interact with the environment, the stealth UAV adjusts the path planning strategy through the rewards obtained from the environment to design the optimal path in real-time. Specifically, by considering the effect of RCS from different angles on the detection probability of the air defense radar, the stealth UAV realizes the iterative optimization of the path planning scheme to improve the reliability of the penetration path. Under the guidance of a goal-directed composite reward function proposed, the convergence speed of the stealth UAV path planning algorithm is improved. The simulation results show that the stealth UAV can reach the target position with the optimal path while avoiding the threat zone.
A simple and efficient flow field visualization method (based on shadow imaging) was applied in a direct-connect test to explore the influence of the momentum flux ratio and the jet angle on the formation and evolution of nitrogen jets in supersonic combustion chambers. The test setup adopts a rectangular flow passage to simulate a flight condition with Mach number of 6 and altitude of 25 km. The experimental results showed that (a) the flow field visualization method adopted in this paper can clearly register the formation and evolution of the shock wave structure in the flow field and the windward shear vortex on the jet surface. (b) The evolution process of the windward shear vortex is significantly affected by the jet angle. In particular, the stretching position of the windward shear vortex changed when the jet angle was obtuse. (c) The bow shocks showed local distortion due to the periodic generation of large-scale shear vortexes. (d) Under the working conditions of the test, the largest instability of the flow field was found for a jet angle of 120°. This work provides, on one hand, the experimental basis for clarifying the formation and evolution mechanism of transverse gas jets, and on the other, valuable data that can be used to validate numerical simulations.
The solid scramjet has become one of the most promising engine types. In this paper, we report the first direct-connect test of a solid scramjet with symmetrical structure, carried out using boron-based fuel-rich solid propellant as fuel. During the test, which simulated a flight environment at Mach 5.6 and 25 km, the performance of the solid scramjet was obtained by measuring the pressure, thrust, and mass flow. The results show that, due to the change in the combustion area of the propellant and the deposition of the throat in the gas generator during the test, the equivalence ratio gradually increased from 0.54 to 0.63. In a solid scramjet, it is possible to obtain a symmetrical distribution of the flow field within the combustor. Moreover, in a multi-cavity combustor, the combustion state expands from the cavity to the center of the flow channel. The performance of the solid scramjet increased during the test, reaching a combustion efficiency of about 42%, a total pressure recovery coefficient of 0.35, and a thrust gain specific impulse of about 418 s. The solid scramjet with symmetrical structure is feasible. The cavity configuration adopted in this paper can reduce the ignition delay time of fuel-rich gas and improve the combustion efficiency of gas-phase combustible components. The shock trains in the isolator are conducive to the recovery of the total pressure. The performance of the solid scramjet is limited by the low combustion efficiency of the particles.
28 October 2021 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Combustion efficiency is the main factor affecting the performance of solid fuel rocket scramjet. To reveal the influence of combustor configuration on performance and further improve combustion efficiency, the influence of the width-height ratio of the rectangle-section combustor on the performance of solid fuel rocket scramjet is investigated numerically in this article. Three-dimensional compressible Reynolds-averaged Navier-Stokes equations coupled with shear stress transport k–ω turbulence model are employed to simulate the aerodynamics. The Euler–Lagrange approach is used to calculate the multiphase flow. Combustion of carbon particles is modeled by the improved Moving Flame Front model. Accuracy of the present numerical model is validated by the experimental data of a rectangle-section combustor from literature. Results show that as the width-height ratio increases, the combustion efficiency increases first and then decreases. The influence of cavity and its position on the performance are also investigated. Results show that cavity can significantly improve combustion efficiency. The effect of cavity position on performance is related to the distribution of particles.