A lot of researchers are closely connected with natural, lignocellulose fibre containing bio-composites producing and studies. Various of polymer matrices, mainly polyolefins, combinations with natural fibres as a reinforcement are used. Our studies are focused on polypropylene based bio-composites containing birch plywood production by-product sanding dust (PSD) accelerated weathering processes. The nine groups of the samples with different composition were exposed in an accelerated weathering chamber for a total duration of the 1032 h. The surface colour, gloss, whiteness degree, micro-hardness and the tensile properties of the samples during the weathering were tested. In addition, the weathered surfaces were characterized by scanning electron microscopy (SEM) studies and by differential scanning calorimetry (DSC) investigations. The obtained results showed the following sight: after the weathering the surface of all samples is faded, also the changes of the gloss and of the whiteness degree occurs, but microhardness of the surface of specimens has decreased. The tensile strength of the samples changes a little, in the same time the tensile modulus increases significantly due to the decrease of the deformation ability of the polypropylene matrix and recrystallization processes in PP. The SEM images taken at the 100 and 500 times of the magnification revealed a lot of the different shape and sizes cracks on the surface of the weathered samples. DSC measurements showed the increase of the degree of crystallinity of the polypropylene after the weathering due to the recrystallization process in the polypropylene matrix.
Wood plastic composites (WPCs) have recently gained attention as alternatives to traditional wood materials for outdoor use, thanks to their enhanced moisture resistance and durability, which extends their service life. Discolouration as well as surface erosion has been observed during weathering for both WPCs with untreated and heat-treated wood. However, aspects such as changes in surface hydrophobicity, chemistry, and erosion in terms of microplastic formation have received less attention; this research aimed to evaluate these factors during natural weathering. Four types of WPC samples, consisting of 50% wood particles (untreated and heat-treated) and 50% polypropylene, were naturally weathered in Latvia for two years. The samples measured 240 mm × 240 mm × 5 mm. Results showed rapid colour changes, microcracks, and exposed wood particles, suggesting microplastic formation. ATR-FTIR analysis showed increased absorption at 1715 cm⁻¹ (carbonyl groups) and at 3410 cm−1 and 3460 cm−1, typical of wood, indicating chemical changes on the surface. These changes influenced surface hydrophobicity, roughness, and water penetration. In a relatively short exposure time, WPCs without proper additives undergo significant changes in their aesthetic and physical properties, leading to surface erosion and potential microplastic formation. This could challenge the perception of WPCs as environmentally friendly materials.
5 April 2019 in IOP Conference Series: Materials Science and Engineering
Article summarizes investigation results of thermal, mechanical and rheological properties of industrially prepared two new wood plastic composites, based on a virgin polypropylene (PP) and birch plywood production residues-plywood sanding dust (PSD). The studies revealed that the tensile strength of composites increased about 25-30% and the modulus for 4.0-4.5 times, but the lightness, the whiteness degree and the common colour changes are smaller in comparison with previously investigated similar composites [5,6].The softening temperatures by VIKA of approbated composites are 154.4 and 158.6°C. The starting temperatures of thermal oxidation are 250.5 and 253.5°C and the thermal expansion of samples at 90°C is only 3%. The rheological experiments showed the decrease of composite melts viscosity with the increase of temperature and the shear rate, but the fluidity index is smaller than 1, that is typical phenomenon for pseudoplastic polymer liquids. The SEM pictures of the fractured surface replicas confirmed that the composites failure has mixed character: partially fracture the polymer matrix and the border surface of polymer matrix and wood fibre.
6 March 2018 in Proceedings of the Estonian Academy of Sciences
Numerous researchers are closely connected with the production and studies of partially green biocomposites. Various polymer matrices, mainly polyolefines and natural fibres as reinforcement and their combinations, are used. Some scientists use various by-products of the timber industry in preparing wood plastic composites (WPCs). Our work is focused on the investigation of exploitation properties (tensile and flexural strength and modulus, impact strength, microhardness, and water uptake) of the WPCs based on the birch plywood production by-product sanding dust (PSD) and the polypropylene (PP) matrix. Sufficiently good fluidity of the composite melts was noted. To clarify the composites fracture mechanism SEM studies were used. For modifying the WPCs maleated polypropylene (MAPP) was used as the coupling agent. It was shown that the additions of PSD and MAPP had a positive influence on the exploitation properties of WPCs based on a PP.
5 April 2019 in IOP Conference Series: Materials Science and Engineering
This research focuses on improving the mechanical properties of linear low density polyethylene (LLDPE) composites reinforced with hemp waste and reducing water absorption. Cross-linking is introduced between the filler and the polymeric matrix. Cleaning the filler surface of dusts with alkali pre-treatment promotes an increase of the aforementioned properties. Hemp waste pre-treatment with TEOS and modified sols decrease composite water absorption and elongation at break, but silanization increase elastic module. The choice of different silanes for the treatment of hemp waste and treatment method affects the properties of composite.