The transient electromagnetic (TEM) method is a widely used nonintrusive geophysical method for ground exploration. Due to the mutual inductance between the transmitter (TX) coil and the receiver (RX) coil, the primary field generated by the emission current reduces the accuracy of the near-surface detection. Because the feature signal [ ] carrying the target information is mainly distributed in the early secondary-field response, the expanded detection signal will reduce the near-surface investigation capability of the TEM device due to the following three aspects: the loss of the proportion of [ ] in the detection signal due to the excessively high primary-field response, the loss of [ ] due to the clipping loss, and the reduction of the noise margin in the case in which the detection signal is magnified. These problems are particularly significant in small-loop devices due to the tight coil distribution. The mutual inductance can be reduced by adjusting the relative positions of the TX and RX coils, a configuration called the weak-coupling coil design. We have analyzed the design principle of the weak-coupling coil design and developed a new design scheme — the crossing-loop design. Simulation results indicate that the crossing-loop design performs superiorly in terms of the detection sensitivity and the investigation depth, compared with the nonweak-coupling coil design and other weak-coupling coil designs such as the gradient coils, opposing coils, and the bucking coil design. The experimental results indicate that the crossing-loop design provides much better near-surface investigation capability than the central-loop device with the same TX coil, which is a typical nonweak-coupling coil design.
19 March 2019 in IEEE Geoscience and Remote Sensing Letters
Transient electromagnetic (TEM) soundings are being increasingly used in engineering applications of environmental and regional surveys and shallow metal detection. Efficient and real time of the processing of the observed TEM data is the trend for the engineering geophysical prospecting and detection instrument in modern times. This letter presents a fast resistivity imaging method of TEM using artificial neural networks. The input-output mapping relations of neural networks are established based on the TEM response characteristics under different transmitter loop devices. The built network could map the recorded TEM data and quickly obtain the resistivity image. The proposed method offers accuracy and fast computation for resistivity imaging, and only 9.003 s costs for the calculation of 142 measured points' data. Feasibility and technical attractiveness of the proposed method in fast resistivity imaging of TEM mean that it is well suited for instantaneous of survey results to a client. The proposed TEM imaging method can be used in real time so that the recorded TEM data can be calculated without retraining, which avoids time-consuming iteration and inversion computation.
18 January 2023 in IEEE Transactions on Geoscience and Remote Sensing
The small-loop transient electromagnetic (TEM) method has great application prospects in shallow surface geophysical exploration. However, the theoretical research on the forward and inversion of this method is obviously lagging behind, which seriously affects the application effect in practical engineering. For the oscillation problem of the small-loop TEM response calculated by using the forward theory of the conventional TEM methods, the dipole integral superposition method was proposed to solve the problem in this paper. The transmitter source is divided into an infinite number of electric dipoles, and the calculation expressions of the electromagnetic field components satisfied by the electric dipoles are deduced, and the forward calculation problem of the layered model of the small-loop TEM method is solved. For the small-loop TEM method inversion problem, the simulated annealing (SA) method was presented for inversion calculation in this paper. First, the influence of the selection of the initial temperature on the inversion result of the SA algorithm was analyzed. Then, we demonstrate the algorithm’s flexibility by choosing different initial models and search ranges and concluded that the different initial models and search ranges don’t affect the inversion results of the SA algorithm. Next, the typical layered models were established and the SA algorithm was used to carry out calculations. The research results show that the SA algorithm is an excellent global optimization algorithm, which can easily jump out of the local minima and converge to the global minima. Finally, we processed the measured data through inversion calculations and compared it with the results of the other three methods to verify the effectiveness and accuracy of the SA algorithm for small-loop TEM data processing. The research content solves the theoretical problem of the small-loop TEM method forward and inversion, promotes the development of the small-loop TEM method technology, and objectively and effectively solves practical engineering application problems.
The transient electromagnetic (TEM) method is widely used in shallow surface engineering geological surveys due to its advantages such as light weight, high efficiency, and strong resolution. However, interpretation and inversion of TEM data is a complicated process. The traditional algorithm of TEM inversion employs the “smoke ring” fast imaging method, which can only reflect the approximate morphology of the stratigraphic model, and the inversion accuracy is low. Therefore, this method cannot meet the requirements of high-precision inversion. In this article, we present the particle swarm optimization (PSO) algorithm for TEM inversion. First of all, the response of the rectangular loop source TEM based on electric dipole integration was calculated and compared with the analytical solution results of the rectangular loop source and the accuracy of the algorithm was verified. Then, we introduced the solution process of the particle swarm optimization algorithm and analyzed the influence of particle swarm optimization algorithm parameter selection on the accuracy of the inversion result and the convergence speed. Next, a layered medium model was established. The particle swarm optimization algorithm and “smoke ring” fast imaging method were used to perform inversion calculation. The results show that the PSO algorithm has the advantages of high efficiency and accuracy. Finally, we examined the effectiveness of the particle swarm optimization algorithm for TEM data processing by inverting survey data from an Air-raid shelter on the campus of Chongqing University in China and comparing the results with those from the “smoke ring” fast imaging. The research works in this article provide new methods and techniques for TEM data processing.
14 January 2021 in IEEE Transactions on Geoscience and Remote Sensing
Transient electromagnetic (TEM) method is widely used in regional mineral resources surveys, environmental engineering geological surveys and shallow surface geophysical exploration, and so on. However, interpretation and inversion of TEM data is a complicated process. The traditional algorithm of TEM inversion employs the “smoke ring” fast imaging method, which can only reflect the approximate morphology of the stratigraphic model, and the inversion accuracy is low. Therefore, this method cannot meet the requirements of high-precision inversion. In this article, we present the firefly algorithm (FA) technology for TEM inversion. First of all, the response of the rectangular loop source TEM based on electric dipole integration was calculated and compared with the analytical solution results of the rectangular loop source and the accuracy of the algorithm was verified. Then, a layered medium model was established. The FA technology and “smoke ring” fast imaging method were used to perform inversion calculation, and the influence of random noise on the accuracy of the FA algorithm was analyzed. The results show that the FA has a high degree of fitting to the model, good anti-noise property, and fast search speed. Next, to illustrate the application effect of the FA algorithm in pseudo 2-D inversion, the 2-D model was established. The results show that the FA algorithm can reflect the distribution of the anomalous body more accurately, especially for the low-resistance anomalous body. Finally, we examined the effectiveness of the FA for TEM data processing by inverting survey data and comparing the results with those from the “smoke ring” fast imaging and particle swarm optimization (PSO) algorithms. The research works provide new methods and techniques for TEM data processing.
19 August 2019 in IET Generation, Transmission & Distribution
Transient electromagnetic (TEM) method is a reliable means of non‐destructive testing for fault diagnosis of grounding grid in substation. In view of the small transmitter loop of the TEM system and many measuring points and survey lines of grounding grid detection in substation. This study presents a fast solution to TEM apparent resistivity imaging for grounding grid detection using artificial neural networks. The input ‐output mapping relation of neural network is established based on TEM response characteristics of the grounding grid. The built network could map the recorded TEM data of grounding grid detection and quickly obtain the resistivity image. The proposed method offers accuracy and fast computation for the resistivity imaging of grounding grid. Feasibility and technical attractiveness of the proposed method in fast imaging of apparent resistivity is investigated with the measurement of grounding grids in the actual substations. It can be used in real time so that the recorded TEM data in substation can be calculated without re‐training, which avoids time‐consuming inversion computation. The rapid processing of massive data and submitting the detection results of the grounding grid to customers rapidly and in real time, which is expectation for a modern power industry.