The small-loop transient electromagnetic (TEM) method has great application prospects in shallow surface geophysical exploration. However, the theoretical research on the forward and inversion of this method is obviously lagging behind, which seriously affects the application effect in practical engineering. For the oscillation problem of the small-loop TEM response calculated by using the forward theory of the conventional TEM methods, the dipole integral superposition method was proposed to solve the problem in this paper. The transmitter source is divided into an infinite number of electric dipoles, and the calculation expressions of the electromagnetic field components satisfied by the electric dipoles are deduced, and the forward calculation problem of the layered model of the small-loop TEM method is solved. For the small-loop TEM method inversion problem, the simulated annealing (SA) method was presented for inversion calculation in this paper. First, the influence of the selection of the initial temperature on the inversion result of the SA algorithm was analyzed. Then, we demonstrate the algorithm’s flexibility by choosing different initial models and search ranges and concluded that the different initial models and search ranges don’t affect the inversion results of the SA algorithm. Next, the typical layered models were established and the SA algorithm was used to carry out calculations. The research results show that the SA algorithm is an excellent global optimization algorithm, which can easily jump out of the local minima and converge to the global minima. Finally, we processed the measured data through inversion calculations and compared it with the results of the other three methods to verify the effectiveness and accuracy of the SA algorithm for small-loop TEM data processing. The research content solves the theoretical problem of the small-loop TEM method forward and inversion, promotes the development of the small-loop TEM method technology, and objectively and effectively solves practical engineering application problems.
The transient electromagnetic (TEM) method is widely used in shallow surface engineering geological surveys due to its advantages such as light weight, high efficiency, and strong resolution. However, interpretation and inversion of TEM data is a complicated process. The traditional algorithm of TEM inversion employs the “smoke ring” fast imaging method, which can only reflect the approximate morphology of the stratigraphic model, and the inversion accuracy is low. Therefore, this method cannot meet the requirements of high-precision inversion. In this article, we present the particle swarm optimization (PSO) algorithm for TEM inversion. First of all, the response of the rectangular loop source TEM based on electric dipole integration was calculated and compared with the analytical solution results of the rectangular loop source and the accuracy of the algorithm was verified. Then, we introduced the solution process of the particle swarm optimization algorithm and analyzed the influence of particle swarm optimization algorithm parameter selection on the accuracy of the inversion result and the convergence speed. Next, a layered medium model was established. The particle swarm optimization algorithm and “smoke ring” fast imaging method were used to perform inversion calculation. The results show that the PSO algorithm has the advantages of high efficiency and accuracy. Finally, we examined the effectiveness of the particle swarm optimization algorithm for TEM data processing by inverting survey data from an Air-raid shelter on the campus of Chongqing University in China and comparing the results with those from the “smoke ring” fast imaging. The research works in this article provide new methods and techniques for TEM data processing.
14 January 2021 in IEEE Transactions on Geoscience and Remote Sensing
Transient electromagnetic (TEM) method is widely used in regional mineral resources surveys, environmental engineering geological surveys and shallow surface geophysical exploration, and so on. However, interpretation and inversion of TEM data is a complicated process. The traditional algorithm of TEM inversion employs the “smoke ring” fast imaging method, which can only reflect the approximate morphology of the stratigraphic model, and the inversion accuracy is low. Therefore, this method cannot meet the requirements of high-precision inversion. In this article, we present the firefly algorithm (FA) technology for TEM inversion. First of all, the response of the rectangular loop source TEM based on electric dipole integration was calculated and compared with the analytical solution results of the rectangular loop source and the accuracy of the algorithm was verified. Then, a layered medium model was established. The FA technology and “smoke ring” fast imaging method were used to perform inversion calculation, and the influence of random noise on the accuracy of the FA algorithm was analyzed. The results show that the FA has a high degree of fitting to the model, good anti-noise property, and fast search speed. Next, to illustrate the application effect of the FA algorithm in pseudo 2-D inversion, the 2-D model was established. The results show that the FA algorithm can reflect the distribution of the anomalous body more accurately, especially for the low-resistance anomalous body. Finally, we examined the effectiveness of the FA for TEM data processing by inverting survey data and comparing the results with those from the “smoke ring” fast imaging and particle swarm optimization (PSO) algorithms. The research works provide new methods and techniques for TEM data processing.
14 September 2023 in IEEE Transactions on Instrumentation and Measurement
In transient electromagnetic (TEM) inverter circuits, a damping resistor is typically connected in parallel to the transmitting coil to prevent overshoot during the turn-off period of the pulse current. This configuration results in an exponential decay waveform for the pulse current, which prolongs the turn-off time and increases the nonlinear error. This article analyzes the impact of the parasitic capacitance on the value of the damping resistor and the end-period waveform of the pulse current base on the inverter circuits, and proposes an optimized control method to reduce both the turn-off time and the nonlinear error of the pulse current. The method is validated through the construction of an experimental circuit. According to the experimental data, this optimization method reduces the turn-off time by 23.8% and the nonlinear error by 5.5%. In the unexploded ordnance (UXO) detection experiment, the optimization method’s detection results exhibit higher resolution.
The water-rich giant karst cave is the risk source of tunnel construction in the karst area. To reduce the risk of tunnel construction, it is necessary to accurately explore the spatial distribution range of the karst cave in the direction of advance and both sides of the tunnel. Reflection seismic and transient electromagnetic (TEM) are the primary geophysical tools for tunnel advanced prediction; they have strengths and weaknesses. The tunnel seismic can only describe the boundary interface between cave bodies and surrounding rock in the direction of advance. Although the TEM method can detect the spatial distribution range of cave bodies, the inversion results depend on the initial resistivity model. The single method is insufficient to describe the spatial distribution of cave bodies. To overcome the shortcoming of a single method, we developed tunnel seismic and TEM joint detection of karst cavern and established a complete data processing flow. The tunnel seismic migration profiles can describe the interface between the karst cave and surrounding rock in the direction of advance. We put forward a reasonable initial model: (1) the layer’s thicknesses are determined by the impedance interface from the tunnel migration data; (2) the initial resistivity values are determined from the pilot hole and prior geological data. Comparison of the inversion results of different initial models of tunnel face horizontal line data proves that the proposed initial model method can reduce multisolution, save calculation time, and improve inversion accuracy. The multidirectional TEM inversion profiles can describe the spatial distribution of the giant cave. Combined with the results of tunnel seismic and TEM, the interpretation errors can be reduced and the extension of the karst cave can be delineated. Later excavation results also verify the accuracy of the prediction results.
This paper proposes a nondestructive, separate transmitter-receiver (TX-RX) electromagnetic measurement system for near-surface detection. Different from the traditional dual-coil integrated design, the proposed transient electromagnetic (TEM) system performs shallow subsurface detection using independent TX coil and movable RX coils. This configuration requires a large primary field so that the far-away secondary field is able to generate reliably induced voltages. To achieve this goal, a bipolar current-pulsed power supply (BCPPS) with a late resonant charging strategy is designed to produce a sufficiently large magnetic moment for the exciting coil with low source interference. The magnetic dipole source (MDS) with a large proportion of weight is separated from the field observation device and does not need to be dragged or transported during the detection process. This setup lowers the weight of the scanning device to 3 kg and greatly improves the measurement efficiency. The results of the laboratory test verify the effectiveness of the separate MDS and RX module system. Field experimental detection further demonstrates that the proposed system can realize highly efficient and shallow surface detection within a 200 m range of the MDS device.