A polarization independent conformal wideband metamaterial absorber has been proposed in this study. The proposed absorber unit cell consists of a circle and a slotted sector, loaded with four lumped resistors between them to improve the absorption bandwidth. Measured and simulated results exhibit more than 90% absorption in the frequency band from 3.90 GHz to 10.5 GHz under the normal incidence angle, and the fractional bandwidth is 91.6%. The proposed absorber is polarization independent due to the symmetrical nature. The absorber unit cell is compact in configuration with a unit cell size of 0.16 λo × 0.16 λo, where λo is the wavelength at 3.9 GHz and the substrate thickness is 0.098 λo. Once the proposed absorber is wrapped on the cylindrical surface, it shows good absorptivity in the absorption frequency band. The effects of many designed parameters have been studied to understand the performance of the wideband absorber. To recognize the absorption phenomenon of the absorber, normalized impedance, electric field distribution, and surface current density have been demonstrated. Finally, the proposed conformal absorber fabricated and measured the absorption for flat and curved surfaces, which exhibits good agreement between the simulated and the experimental results.
In the paper, a compact quad-band polarization-independent metasurface absorber has been presented for different microwave frequency bands. The proposed absorber unit cell comprises of two square and two concentric circular rings and it exhibits the absorption peaks greater than 90% at 3.1 GHz, 5.5 GHz, 7.6 GHz and 10.98 GHz respectively under the normal incidence. The full width at half maximum (FWHM) bandwidth is 150 MHz (3.03-3.18 GHz), 180 MHz (5.38-5.56 GHz), 330 MHz (7.44-7.77 GHz), and 560 MHz (10.70-11.26 GHz) at the four frequency bands. The proposed absorber is polarization and incidence angle insensitive due its symmetrical structure which has been confirmed by simulated results. The proposed structure also shows more than 90% absorptivity up to 60o incidence angle. The absorber unit cell is compact in configuration with unit cell size of 0.12λo× 0.12λo and ultrathin thickness of 0.016 λo, where λo is the wavelength at lowest frequency absorption peak. To recognize the absorption phenomenon of the absorber, input impedance, E-field and surface current distribution characteristics have been demonstrated. The structure has been fabricated and it shows good accord between simulated and measured results.
A polarisation independent conformal absorber has been proposed for X‐band microwave application. The absorber unit cell consists of three resonators, which generate three absorption bands at 9.1, 11.04 and 11.44 GHz with more than 90% absorption. The full wave at half maximum bandwidth of the absorber is 320 and 720 MHz at lower and upper‐frequency bands. The absorber is conformal as it has a low‐profile flexible substrate with an ultrathin thickness of 0.01 λo , where λo is the wavelength at 9.1 GHz. The proposed absorber unit cell has a fourfold symmetry, which makes the absorber polarisation independent and possesses a wide angle stability under oblique incident angle up to 50°. The absorption performance of the absorber on various radii of cylindrically curved surface has been confirmed through the simulated and measured results.
In the article, polarization and incident-angle independent metasurface absorber for X-band application has been proposed. Proposed absorber unit cell composed of a circular sector attached to a cross-shaped structure. The proposed absorber is symmetrical along the horizontal and vertical axis, which supports polarization angle insensitivity. Metasurface absorber shows the very good impedance matching with free space at 10.48 GHz along with 97% absorptivity. The full width at half maximum (FWHM) bandwidth is 480 MHz (10.24-10.72 GHz). In transverse electric and magnetic (TE and TM), modes the absorptivity of the proposed absorber is maintained above 90% up to 60o incidence angle. The absorber has an ultrathin thickness of 0.028λo, where λo is the wavelength of absorption peak. The absorption phenomenon is explained by normalized impedance, E-field distribution and surface current density. To analyze the metasurface properties permittivity, permeability and dispersion diagram has been demonstrated. The metasurface absorber has been fabricated and it shows the good accord between simulated and measured results.
13 August 2019 in International Journal of RF and Microwave Computer-Aided Engineering