Piotr Ramiaczek

Dr. Piotr Ramiaczek


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
Marek IwańskiMarek Iwański
Marek Iwański
Anna Chomicz-KowalskaAnna Chomicz-Kowalska
Anna Chomicz-Kowalska
Grzegorz MazurekGrzegorz Mazurek
Grzegorz Mazurek
Przemysław BuczyńskiPrzemysław Buczyński
Przemysław Buczyński
/C/ Cholewinska
/ Cholewinska
PRPiotr Ramiaczek
Piotr Ramiaczek
The process of water-based foaming of bitumen produces binders that can be incorporated in cold recycled asphalt mixes and pavement upper structural layers made of half-warm mix asphalt prepared at 100–130 °C. During the foaming process, cold water and air act on hot bitumen (160–170 °C), which results in the explosive vaporization of water leading to changes in the binder structure. The impact of foaming on the properties of bitumen 70/100 was evaluated by investigating the binder characteristics before and after foaming. Determination of two foaming parameters, maximum expansion and half-life, was followed by measurements of penetration at 25 °C, softening point, Fraass breaking point, and dynamic viscosity at 60, 90, and 135 °C. Rheological and low-temperature tests were also performed before and after foaming bitumen 70/100. The Bending Beam Rheometer method was applied to determine the low temperature stiffness modulus. A DHR-2 rheometer was used to determine the dynamic modulus and phase angle of the tested binder. The Black and master curves before and after foaming were plotted in the 2S2P1D model and the model parameters were analysed. Analysis of the test results confirmed the effects of the foaming process on the basic, low-temperature, and rheological characteristics of the bitumen.

RKRobert Kowalik
Robert Kowalik
JGJarosław Ireneusz Gawdzik
Jarosław Ireneusz Gawdzik
PBPaulina Bąk-Patyna
Paulina Bąk-Patyna
PRPiotr Ramiaczek
Piotr Ramiaczek
Nebojša JuriševićNebojša Jurišević
Nebojša Jurišević
More and more attention in sewage sludge management is being devoted to its environmental utilization. This approach is justified both from economic and environmental points of view. However, as with any method, there are certain possibilities and limitations. The goal of the natural utilization of sewage sludge is to recover the valuable agronomic properties and fertilizing potential of the sludge. The main aspect limiting the possibility of using sludge as a fertilizer is the heavy metal content. In this paper, an analysis of the risk of environmental contamination in the case of application of sewage sludge with different forms of sludge treatment was carried out. Risk indices such as Igeo and PERI, based on the comparison of total metal content in sludge and soil, as well as RAC and ERD indices, which take into account the mobility of metals in soil, were calculated. It was shown that high levels of potential risk and geoaccumulation indicators do not necessarily disqualify the use of sewage sludge, the key aspect is the form of mobility in which the heavy metals are found in the sludge, and this should be the only aspect taken into account for the possibility of their environmental use.

20 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
Krzysztof MaciejewskiKrzysztof Maciejewski
Krzysztof Maciejewski
PRPiotr Ramiaczek
Piotr Ramiaczek
EREva Remisova
Eva Remisova
The presented study explores the effects of decreased temperatures utilized in rolling thin-film oven (RTFOT) laboratory short-term ageing of asphalt binders based on 35/50- and 50/70-penetration paving-grade bitumen. Additionally, the effects of three additives used with these binders at different concentrations are evaluated: liquid anti-stripping agent, liquid warm-mix additive, and solid warm-mix additive. The resulting asphalt binders were subjected to basic (penetration at 25 °C, softening point, dynamic viscosity) and functional high-temperature characterization (G*/sin(δ), high critical temperature, non-recoverable creep compliance). It was found that the decreased short-term ageing temperatures may detrimentally impact the high-temperature grade of bituminous binders, but this effect can be mitigated by the use of appropriate additives. What is more, it was found that bituminous binders may respond differently to the aforementioned factors. Based on the results, it is advised that asphalt binders intended for use in warm-mix asphalts should be thoroughly tested to appropriately simulate the mixture production process and its effects.

22 January 2025 in Materials
Verified
Journal Article
Open access
PDF file
JSJustyna Stępień
Justyna Stępień
Anna Chomicz-KowalskaAnna Chomicz-Kowalska
Anna Chomicz-Kowalska
MTMagdalena Tutaj-Dudała
Magdalena Tutaj-Dudała
MDMichał Dudała
Michał Dudała
Krzysztof MaciejewskiKrzysztof Maciejewski
Krzysztof Maciejewski
MIMateusz Iwański
Mateusz Iwański
The present study investigates the effects of different compaction methods on the properties of roller-compacted concrete (RCC) used for road pavements. The study focuses on comparing the Proctor compaction method utilizing different compaction efforts and molds (2.5 kg rammer with three layers of 56 blows and 4.5 kg with three and five layers of 56 blows, cylindrical and cube molds) with a slab compactor in static and vibratory setting. The samples produced in a slab compactor were obtained by drilling from the prepared slab. The evaluated properties of the samples included compressive strength and bulk density. The study involved a C25/30 concrete with the intention to be used in low volume roads according to national standards. The study concluded that the utilization of Proctor compaction and slab compactor with vibratory setting provided similar levels of strength performance of the RCC mixture, regardless of the shape of the Proctor compacted samples. In terms of the bulk densities, the main differentiating factor in the case of Proctor compaction was the weight of the rammer. The compressive strength of the samples was also strongly related to their bulk densities.

31 March 2023 in Roads and Bridges – Drogi i Mosty
Verified
Journal Article
Open access
PDF file
Marek IwańskiMarek Iwański
Marek Iwański
Grzegorz MazurekGrzegorz Mazurek
Grzegorz Mazurek
ACAnna Chomicz-Kowalska
Anna Chomicz-Kowalska
Przemysław BuczyńskiPrzemysław Buczyński
Przemysław Buczyński
MCMałgorzata Cholewińska
Małgorzata Cholewińska
PRPiotr Ramiaczek
Piotr Ramiaczek
Rozwój prac modernizacyjnych dróg różnych kategorii, od autostrad po drogi samorządowe, przyczynia się do powstawania dużej ilości destruktu asfaltowego (RAP) o zróżnicowanej jakości i uziarnieniu. W ramach gospodarki zrównoważonej niezbędne jest jego ponowne wykorzystanie. Obecnie w większości przeznaczony jest on do wytworzenia recyklowanych mieszanek mineralno-asfaltowych wbudowywanych w warstwę podbudowy. Zróżnicowana jakość destruktu wymaga zastosowania odpowiedniego rodzaju spoiwa, tak aby można było go wykorzystać w optymalny sposób. W związku z tym zaistniała potrzeba opracowania spoiwa hydraulicznego mieszanego, które składa się z cementu CEM I 32.R, wapna hydratyzowanego Ca(OH)2 oraz ubocznych cementowych produktów pylastych (UCPP) dobieranych w odpowiednich proporcjach. Badano wpływ składu spoiwa hydraulicznego mieszanego na następujące właściwości mieszanki wytwarzanej z zastosowaniem asfaltu spienionego: zawartość wolnych przestrzeni, wytrzymałość na pośrednie rozciąganie, wytrzymałość na osiowe ściskanie, odporność na oddziaływanie wilgoci i mrozu wg czterech różnych parametrów oraz moduł sztywności w temperaturze -10oC, +13oC, +25oC i +40oC wg metody IT-CY. Na podstawie wykonanych badań ustalono rekomendowany skład spoiwa zapewniający wymagane właściwości recyklowanej mieszanki związanej spoiwem hydraulicznym i asfaltem spienionym.

6 September 2026 in Materials
Verified
Journal Article
Open access
PDF file
JSJustyna Stępień
Justyna Stępień
Krzysztof MaciejewskiKrzysztof Maciejewski
Krzysztof Maciejewski
PRPiotr Ramiaczek
Piotr Ramiaczek
Anna Chomicz-KowalskaAnna Chomicz-Kowalska
Anna Chomicz-Kowalska
Reducing asphalt mixture production temperatures and partially replacing virgin aggregates with industrially derived materials are potential pathways toward more sustainable pavement technologies. This study evaluated the effects of steel slag (SS) aggregate and air-cooled blast furnace slag (ACBFS) aggregate on the properties of asphalt concrete for pavement binder courses produced as warm-mix asphalt (WMA) using water-foamed bitumen. The reference hot-mix asphalt (HMA) and WMA mixtures were compared with WMA variants in which 20% or 40% of the virgin aggregate was replaced by SS or ACBFS. The slag aggregates were characterized by physical and mechanical properties, surface morphology, and local elemental composition. Mixture performance was evaluated based on air voids content, indirect tensile strength, water and freeze–thaw resistance, dynamic modulus, and rutting resistance, followed by statistical analysis. Slag type and replacement level affected the properties differently. Increasing slag content increased air voids content, whereas slag-containing mixtures showed a lower relative loss of tensile strength after conditioning than the reference mixtures. Compared with SS, ACBFS resulted in lower dynamic modulus and poorer rutting resistance. The mixture containing 20% SS satisfied all adopted technical requirements. The results support the use of SS at this replacement level, whereas ACBFS mixtures require further optimization.