Optical coherence tomography (OCT) has recently attracted a lot of interest in the pharmaceutical manufacturing industry as a fast, contactless and non-destructive modality for quantifying thin film coatings on pharmaceutical dosage forms, which cannot be resolved easily with other techniques. In this topical review, we present an overview of the research that has been performed to date, highlighting key differences between systems and outlining major challenges ahead.
Automotive coating systems are designed to protect vehicle bodies from corrosion and enhance their aesthetic value. The number, size and orientation of small metallic flakes in the base coat of the paint has a significant effect on the appearance of automotive bodies. It is important for quality assurance (QA) to be able to measure the properties of these small flakes, which are approximately 10μm in radius, yet current QA techniques are limited to measuring layer thickness. We design and develop a time-domain (TD) full-field (FF) optical coherence tomography (OCT) system to scan automotive panels volumetrically, non-destructively and without contact. We develop and integrate a segmentation method to automatically distinguish flakes and allow measurement of their properties. We test our integrated system on nine sections of five panels and demonstrate that this integrated approach can characterise small flakes in automotive coating systems in 3D, calculating the number, size and orientation accurately and consistently. This has the potential to significantly impact QA testing in the automotive industry.
1 October 2017 in Journal of Pharmaceutical Sciences
Optical coherence tomography (OCT) has recently been demonstrated to measure the film coating thickness of pharmaceutical tablets and pellets directly. The results enable the analysis of inter- and intra-tablet coating variability at an off-line and in-line setting. To date, only a few coating formulations have been tried and there is very little information on the applicability of OCT to other coatings. As it is well documented that optical methods including OCT are prone to scattering leading to limited penetration, some pharmaceutical coatings may not be measurable altogether. This study presents OCT measurements of 22 different common coatings for the assessment of OCT applicability.
17 March 2017 in International Journal of Remote Sensing
Mapping urban areas at the regional and global scales has been used in ecology, environment, sociology, and other subjects. Recently, it has become increasingly popular to extract urban areas from night-time light remote-sensing data. In this article, we reported an alternative method to extract information of urban areas from VIIRS Day/Night Band (DNB) and MODIS normalized differential vegetation index (NDVI) data based on the adaptive mutation particle swarm optimization (AMPSO) algorithm and the Support Vector Machine (SVM) classification algorithm. This method was validated using the urban areas of nine Chinese cities classified from Landsat Enhanced Thematic Mapper (ETM+) images by object-oriented image classification technology. We demonstrated that this new method for urban area extraction had a good classification coherency with the Landsat8 OLI result. In addition, it is more robust than other classification methods, and can be used to characterize the inter-urban texture as well.
23 March 2021 in IEEE Transactions on Power Electronics
Bonding wires are one of the most failure-prone components of power electronics’ modules, and silicone gel is usually employed to encase bonding wires. To study the deformation of silicone gel-encased bonding wires, in this article, we report the use of line-field optical coherence tomography (LF-OCT) technique to precisely measure the electrical–thermal–mechanical (ETM) deformation of bonding wires. An LF-OCT system was developed to capture the whole cross-sectional image (B-scan) of the bonding wire sample in a single-shot fashion due to its advantageous parallel detection scheme. This, together with the Fourier phase self-referencing technique, allows the deformation of the bonding wires to be quantitatively measured down to the range of 0.1 nm. The maximum sampling rate (framerate) of the deformation measurement achieved was 400 Hz when setting camera imaging size to 1920 × 200 pixels, providing a temporal resolution of 2.5 ms for monitoring the ETM deformation dynamics of the bonding wire. We found that the ETM deformation of the gel-encased bonding wire was about three times smaller than that of the bare bonding wire. These results represent the first experimental demonstration that the LF-OCT could be a useful analytical tool for studying the time-dependent ETM deformation of bonding wires encased by silicone gel.
In the laundry industry, colorimetry is a common way to evaluate the stain removal efficiency of detergents and cleaning products. For ease of visualization, the soiling agent is treated with a dye before measurement. However, it effectively measures the dye removal rather than stain removal, and it cannot provide depth-resolved information of the sample. In this study, we show that full-field (FF) optical coherence tomography (OCT) technique is capable of measuring the cleaning effect on cotton fabric by imaging the sub-surface features of fabric samples. We used a broadband light-emitting diode (LED) source to power the FF-OCT system that achieves the resolution of 1 µm axially and 1.6 µm laterally. This allows the micron-sized cotton fibres/fibrils at different depth positions to be resolved. The clean, the soiled, and the washed samples can be differentiated from their cross-sectional images using OCT, where the cleaning effect can be correlated with the sub-surface fibre volume. The experimental results of the proposed method were found to be in good agreement with those of the standard colorimetry method. The proposed technique therefore offers an alternative way for measuring the stain removal from fabric substrate to assess the effectiveness of laundry detergent products.