Copper sulfide layers were formed on polyamide PA 6 surface using the sorption‐diffusion method. Polymer samples were immersed for 4 and 5 h in 0.15 mol⋅ dm−3 K2S5O6 solutions and acidified with HCl (0.1 mol⋅ dm−3) at 20∘C. After washing and drying, the samples were treated with Cu(I) salt solution. The samples were studied by UV/VIS, X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS) methods. All methods confirmed that on the surface of the polyamide film a layer of copper sulfide was formed. The copper sulfide layers are indirect band‐gap semiconductors. The values of Ebg are 1.25 and 1.3 eV for 4 h and 5 h sulfured PA 6 respectively. Copper XPS spectra analyses showed Cu(I) bonds only in deeper layers of the formed film, while in sulfur XPS S 2p spectra dominating sulfide bonds were found after cleaning the surface with Ar+ ions. It has been established by the XRD method that, beside Cu2S, the layer contains Cu1.9375S as well. For PA 6 initially sulfured 4 h, grain size for chalcocite, Cu2S, was ∼35.60 nm and for djurleite, Cu1.9375S, it was 54.17 nm. The sheet resistance of the obtained layer varies from 6300 to 102 Ω/cm2.
In the present research diamond-like carbon (DLC) films containing 4–29 at.% of silicon were deposited by reactive magnetron sputtering of carbon target. Study by X-ray photoelectron spectroscopy revealed the presence of Si–C bonds in the films. Nevertheless, a significant amount of Si–O–C and Si–Ox bonds was present too. The shape of the Raman scattering spectra of all studied diamond-like carbon containing silicon (DLC:Si) films was typical for diamond-like carbon. However, some peculiarities related to silicon doping were found. Studies on the dependence of DLC:Si of the optical transmittance spectra on the Si atomic concentration have shown that doping by silicon affects linear, as well as nonlinear, optical properties of the films. It is shown that the normalized reflectance of DLC:Si films decreased with the increased exciting light fluence. No clear relation between the normalized reflectance and photoexcited charge carrier relaxation time was found. It was suggested that that the normalized reflectance decrease with fluence can be related to nonlinear optical properties of the hydrogenated diamond-like carbon phase in DLC:Si film.
A facile and feasible protocol for synthesis of functionalized reduced graphene oxide decorated with gold nanoparticles (AuNP/rGO) in mild reaction conditions has been successfully developed. Starting from graphite, the following synthesis routes were developed: 1) preparation of graphite oxide; 2) graphene oxide (GO) functionalized with a compatible polymer; 3) reduced graphene oxide decorated with gold nanoparticles (final compound). The surface morphology of as-prepared AuNP/rGO was investigated using scanning electron microscopy (SEM) and specific surface area was determined using BET method, while structural properties were investigated using Raman scattering spectroscopy, X-Ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR). This comprehensive study demonstrated the simultaneous reduction of GO and the achievement of Au nanoparticles dispersed on graphene sheets. An ORR catalytic system containing prepared AuNP/rGO was developed, and electrochemical measurements were performed. Firstly, the ex-situ electrochemical performances of AuNP/rGO-modified carbon electrode were investigated using cyclic voltammetry. Secondly, the in-situ electrochemical evaluation were carried out as application in real PEM fuel cell and analyzed as comparison commercial Pt/C versus developed ORR catalytic system. The in-situ CV results showed that the oxidation and reduction peaks corresponding to hydrogen adsorption/desorption decreased differently, indicating that a decrease of electrochemical surface area occurs for both cases, more visible for commercial catalyst. The cathode made with AuNP/rGO developed in this work, tested in hydrogen-air PEMFC, had a power density of 0.59 W cm − 2 at 0.6 V, a meaningful voltage for fuel cells operation, comparable with that of a commercial Pt-based cathode tested under identical conditions, but a superior electrochemical stability. The results confirmed that the developed AuNP/rGO nanoparticles could be valuable alternative ORR nanostructured electrodes.
Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is the most successful transparent conductive polymer widely used in functional organic devices. However, its potential in fabrication of highly conductive electrodes still has not been fully explored. This paper is an attempt to fill the existing gap of knowledge on possible post-treatments of dimethyl sulfoxide (DMSO)-doped PEDOT:PSS thin films. In the present study, surface morphology, optical and electrical properties of untreated and sulfuric acid treated DMSO-doped PEDOT:PSS multilayers on the glass coverslip substrates are examined. It is demonstrated that short-time sulfuric acid treatment enhances electrical and optical properties, and smoothens surface of the transparent conductive films. Enhancement of electrical conductivity by more than 30 % can be associated with increase in doping level, removal of excess PSS and accompanied shape alterations of the conjugated PEDOT chains. Acid treatment also results in smoother transmittance spectra and a slight improvement of optical transparency. Hence, sulfuric acid post-treatment can be considered as a simple and inexpensive technique for the complementary doping of DMSO-doped PEDOT:PSS films with the aim to develop the more effective transparent electrodes.