Sajid Alvi

Mr. Sajid Alvi


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 February 2019 in Metals
Verified
Journal Article
Open access
PDF file
KSKamran Saeidi
Kamran Saeidi
SASajid Alvi
Sajid Alvi
FLFrantišek Lofaj
František Lofaj
VPValeri Ivanov Petkov
Valeri Ivanov Petkov
FAFarid Akhtar
Farid Akhtar
Duplex stainless steel, 71 wt.% austenite, 13 wt.% ferrite and 16 wt.% sigma, was made upon heat treating of fully ferritic as-built selective laser melted (SLM) 2507 stainless steel at 1200 °C. Formation of sigma phase in the heat treated SLM 2507 was investigated using optical microscopy and scanning electron microscopy (SEM). The heat treated SLM 2507 demonstrated a yield strength of 686 MPa, ultimate tensile strength of 920 MPa and an elongation of 1.8% at room temperature with a brittle fracture morphology. Precipitation of sigma phase during heat treatment and slow cooling improved the mechanical and wear properties at high temperatures (1200 °C and 800 °C, respectively). The tensile strength and elongation of the heat treated SLM 2507 was measured 400 MPa and 20% as compared to casted duplex steel with 19 MPa and 30% elongation at 1200 °C. The 20 times higher mechanical strength as compared to casted duplex steel was attributed to sigma precipitates. Tribological behaviour of heat treated duplex SLM 2507 containing sigma at 800 °C showed very low wear rate of 4.5 × 10−5 mm3/mN compared to casted duplex steel with 1.6 × 10−4 mm3/mN.

13 November 2020 in Metals
Verified
Journal Article
Open access
PDF file
SASajid Alvi
Sajid Alvi
Owais WaseemOwais Waseem
Owais Waseem
FAFarid Akhtar
Farid Akhtar
The phase stability, compressive strength, and tribology of tungsten alloy containing low activation elements, W0.5(TaTiVCr)0.5, at elevated temperature up to 1400 °C were investigated. The spark plasma sintered W0.5(TaTiVCr)0.5 alloy showed body centered cubic (BCC) structure, which was stable up to 1400 °C using in-situ high temperature XRD analysis and did not show formation of secondary phases. The W0.5(TaTiVCr)0.5 alloy showed exceptionally high compressive yield strength of 1136 ± 40 MPa, 830 ± 60 MPa and 425 ± 15 MPa at 1000 °C, 1200 °C and 1400 °C, respectively. The high temperature tribology at 400 °C showed an average coefficient of friction (COF) and low wear rate of 0.55 and 1.37 × 10−5 mm3/Nm, respectively. The superior compressive strength and wear resistance properties were attributed to the solid solution strengthening of the alloy. The low activation composition, high phase stability, superior high temperature strength, and good wear resistance at 400 °C of W0.5(TaTiVCr)0.5 suggest its potential utilization in extreme applications such as plasma facing materials, rocket nozzles and industrial tooling.

10 October 2018 in Scientific Reports
Verified
Journal Article
Open access
PDF file
SASajid Alvi
Sajid Alvi
FAFarid Akhtar
Farid Akhtar
Polymer derived ceramic (PDC) composite coatings were deposited on AISI 304 substrates using siloxane based preceramic polymer polymethlysilsquioxane (PMS) and ZrSi2as active filler or Ag as passive filler. The tribological performance of the composite coatings was evaluated at room temperature and moderately high temperatures (150 °C, 200 °C, 300 °C and 400 °C). The composite coatings showed low coefficient of friction (COF), µ, from 0.08 to 0.2 for SiOC-ZrSi2composite coatings, and from 0.02 to 0.3 for SiOC-Ag composite coatings, at room temperature with increasing normal load from 1 to 5 N. High temperature tribology tests showed high COF values from 0.4 to 1 but low wear for SiOC-ZrSi2coating, and low COF from 0.2 to 0.3 for SiOC-Ag coatings at lower temperature ranges. Low load friction tests at room temperature showed negligible wear in SiOC-ZrSi2coatings, suggesting good wear resistant and lubricating properties due to formation of t-ZrO2and carbon. Low COF and high amount of wear was observed in SiOC-Ag composite coatings at room temperature due to high ductility of Ag and smearing of wear debris in the wear track. The coatings and wear tracks were characterized to evaluate the lubrication and wear behavior.

24 June 2020
Verified
Book Chapter
Open access
PDF file
SASajid Alvi
Sajid Alvi
HZHanzhu Zhang
Hanzhu Zhang
FAFarid Akhtar
Farid Akhtar
High-entropy ceramics is an emerging class of high-entropy materials with properties superior to conventional ceramics. Recent research has been focused on the development of new high-entropy ceramic compositions. High-entropy oxides, carbides, borides, silicides, and boron carbides had been reported with superior mechanical, oxidation, corrosion, and wear properties. The research work on the processing and characterization of bulk high-entropy ceramics and coating systems has been summarized in this chapter. The composition design, structure, chemistry, composite processing of bulk high-entropy ceramics, and evolution of microstructure and properties are reported. The literature on the deposition of high-entropy ceramic coating and the influence of coating parameters have been discussed to produce high-entropy ceramic coatings with superior mechanical, oxidation, and wear properties.