František Lofaj

Prof. František Lofaj

Institute of Materials Research Slovak Academy of Sciences, Kosice, Slovakia
orcid

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2015 in RSC Advances
Verified
Journal Article
Closed access
PDF file
KSKamran Saeidi
Kamran Saeidi
LKLenka Kvetková
Lenka Kvetková
FLFrantišek Lofaj
František Lofaj
ZSZhijian Shen
Zhijian Shen
An austenitic stainless steel was prepared by laser melting. High resolution transmission electron microscopy with energy dispersive spectrometry confirmed the in situ formation of oxide nanoinclusions with average size less than 50 nm. Scanning electron microscopy examination revealed the homogeneous dispersion of the oxide nanoinclusions in the steel matrix. The tensile and yield strengths of the prepared specimens were 703 and 456 MPa respectively with high ductility which is significantly improved compared to its conventionally casted counterpart.

1 October 2013 in Journal of the European Ceramic Society
Verified
Journal Article
Closed access
ADAnnamaria Duszová
Annamaria Duszová
RHRadoslav Halgaš
Radoslav Halgaš
MBMarek Bľanda
Marek Bľanda
PHPavol Hvizdos
Pavol Hvizdos
FLFrantišek Lofaj
František Lofaj
JMJerzy Morgiel
Jerzy Morgiel

1 September 2004 in Journal of Non-Crystalline Solids
Verified
Journal Article
Closed access
FLFrantišek Lofaj
František Lofaj
SDSébastien Dériano
Sébastien Dériano
MLMarie LeFloch
Marie LeFloch
TRTanguy Rouxel
Tanguy Rouxel
MHMichael J. Hoffmann
Michael J. Hoffmann

1 October 2019 in Additive Manufacturing
Verified
Journal Article
Open access
KSKamran Saeidi
Kamran Saeidi
DZDaniel Leon Zapata
Daniel Leon Zapata
FLFrantišek Lofaj
František Lofaj
LKLenka Kvetkova
Lenka Kvetkova
JOJon Olsen
Jon Olsen
FAFarid Akhtar
Farid Akhtar

8 February 2019 in Metals
Verified
Journal Article
Open access
PDF file
KSKamran Saeidi
Kamran Saeidi
SASajid Alvi
Sajid Alvi
FLFrantišek Lofaj
František Lofaj
VPValeri Ivanov Petkov
Valeri Ivanov Petkov
FAFarid Akhtar
Farid Akhtar
Duplex stainless steel, 71 wt.% austenite, 13 wt.% ferrite and 16 wt.% sigma, was made upon heat treating of fully ferritic as-built selective laser melted (SLM) 2507 stainless steel at 1200 °C. Formation of sigma phase in the heat treated SLM 2507 was investigated using optical microscopy and scanning electron microscopy (SEM). The heat treated SLM 2507 demonstrated a yield strength of 686 MPa, ultimate tensile strength of 920 MPa and an elongation of 1.8% at room temperature with a brittle fracture morphology. Precipitation of sigma phase during heat treatment and slow cooling improved the mechanical and wear properties at high temperatures (1200 °C and 800 °C, respectively). The tensile strength and elongation of the heat treated SLM 2507 was measured 400 MPa and 20% as compared to casted duplex steel with 19 MPa and 30% elongation at 1200 °C. The 20 times higher mechanical strength as compared to casted duplex steel was attributed to sigma precipitates. Tribological behaviour of heat treated duplex SLM 2507 containing sigma at 800 °C showed very low wear rate of 4.5 × 10−5 mm3/mN compared to casted duplex steel with 1.6 × 10−4 mm3/mN.

1 January 2002 in Journal of the European Ceramic Society
Verified
Journal Article
Closed access
FLFrantišek Lofaj
František Lofaj
SWSheldon M. Wiederhorn
Sheldon M. Wiederhorn
GLGabrielle G. Long
Gabrielle G. Long
BHBernard J. Hockey
Bernard J. Hockey
PJPete R. Jemian
Pete R. Jemian
UTUlrike Täffner
Ulrike Täffner