To address the resource-competing issue between high sensitivity and wide working range for a stand-alone sensor, development of capacitive sensors with an adjustable gap between two electrodes has been of growing interest. While several approaches have been developed to fabricate tunable capacitive sensors, it remains challenging to achieve, simultaneously, a broad range of tunable sensitivity and working range in a single device. In this work, a 3D capacitive sensor with a seesaw-like shape is designed and fabricated by the controlled compressive buckling assembly, which leverages the mechanically tunable configuration to achieve high-precision force sensing (resolution ~5.22 nN) and unprecedented adjustment range (by ~33 times) of sensitivity. The mechanical tests under different loading conditions demonstrate the stability and reliability of capacitive sensors. Incorporation of an asymmetric seesaw-like structure design in the capacitive sensor allows the acceleration measurement with a tunable sensitivity. These results suggest simple and low-cost routes to high-performance, tunable 3D capacitive sensors, with diverse potential applications in wearable electronics and biomedical devices.
We proposed a novel kind of absolute capacitive grating displacement measuring system with both high accuracy and long range in a previous article. The measuring system includes both a MOVER and a STATOR, the contact surfaces of which are coated by a thin layer of dielectric film with a low friction coefficient and high hardness. The measuring system works in contact mode to minimize the gap changes. This paper presents a theoretical analysis of the influence of some factors, including fabrication errors, installation errors, and environment disturbance, on measurement signals. The measuring signal model was modified according to the analysis. The signal processing methods were investigated to improve the signal sensitivity and signal-to-noise ratio (SNR). The displacement calculation model shows that the design of orthogonal signals can solve the dead-zone problem. Absolute displacement was obtained by a simple method using two coarse signals and highly accurate displacement was further obtained while using two fine signals with the help of absolute information. According to the displacement calculation model and error analysis, the error in fine calculation functions mainly determines the model’s accuracy and is locally affected by coarse calculation functions. It was also determined that amplitude differences, non-orthogonality, and signal offsets are not related to the accuracy of the displacement calculation model. The experiments were carried out to confirm the abovementioned theoretical analysis. The experimental results show that the displacement resolution and error in the displacement calculation model reach ±4.8 nm and ±34 nm, respectively, in the displacement range of 5 mm. The experiments and the theoretical analyses both indicate that our proposed measuring system has great potential for achieving an accuracy of tens of nanometers and a range of hundreds of millimeters.
22 August 2017 in Journal of Micromechanics and Microengineering
This paper presents structure design, microfabrication processes, calibration techniques and experimental results of differential capacitance force sensors with features of sub-nano-newton sensitivity, up to 10 000 Hz sampling rate, and applicability as stand-alone devices. The representative sensor demonstrates a force resolution of 0.11 nN at a 19 Hz sampling rate or 1.47 nN at 10 000 Hz. A novel asymmetric differential capacitance structure proposed results in remarkable increase in the ratio of measurement range to resolution in comparison with traditional symmetric structure. In addition, the stiction between silicon and glass caused by the capillary force during dicing is eliminated by the use of hydrophobization treatment. Such a treatment is essential to successfully fabricate structures with a large ratio of overlapped area to gap in silicon/glass anodic bonding processes.
Structural superlubricity (SSL) is a state of nearly zero friction and zero wear between two directly contacted solid surfaces. Recently, SSL was achieved in mesoscale and thus opened the SSL technology which promises great applications in Micro-electromechanical Systems (MEMS), sensors, storage technologies, etc. However, load issues in current mesoscale SSL studies are still not clear. The great challenge is to simultaneously measure both the ultralow shear forces and the much larger normal forces, although the widely used frictional force microscopes (FFM) and micro tribometers can satisfy the shear forces and normal forces requirements, respectively. Here we propose a hybrid two-axis force sensor that can well fill the blank between the capabilities of FFM and micro tribometers for the mesoscopic SSL studies. The proposed sensor can afford 1mN normal load with 10 nN lateral resolution. Moreover, the probe of the sensor is designed at the edge of the structure for the convenience of real-time optical observation. Calibrations and preliminary experiments are conducted to validate the performance of the design.