Jens Reimann

Dr. Jens Reimann

Institut für Hochfrequenztechnik und Radarsysteme, Deutsches Zentrum für Luft- und Raumfahrt, Weßling, Germany
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 March 2020 in Remote Sensing
Verified
Journal Article
Open access
PDF file
KSKersten Schmidt
Kersten Schmidt
MSMarco Schwerdt
Marco Schwerdt
NMNuno Miranda
Nuno Miranda
JRJens Reimann
Jens Reimann
Radiometric calibration adjusts the measured pixel intensity to a physical property, the radar cross section (RCS). After calibration, this relationship is defined over the entire backscatter range: from low image power (near noise) up to high reflections (below saturation). Based on a proper radiometric calibration, the measured radar backscatter for the Sentinel-1 synthetic aperture radar (SAR) satellite constellation is validated over a wide backscatter range using different target types. Therefore, the RCS derived from point targets and radar brightness from distributed targets are compared between Sentinel-1A (S-1A) and Sentinel-1B (S-1B) acquisitions over the same observation area for regions where a stable target backscatter is expected for a certain period of time. Low differences (in the order of 0.3 dB) are found between S-1A and S-1B for high and medium backscatter derived from point targets or rainforest regions, but higher differences for low backscattering regions like ice areas and lakes. For comparing radar brightness containing low backscatter targets, an accurate derived noise level has to be taken into account. In addition to the measured lower noise equivalent beta zero (NEBZ) level, higher transmit power was detected for S-1B compared to S-1A. The higher antenna gain of S-1B leads finally to a higher sensitivity for low backscattering areas of S-1B compared to S-1A and explains the found differences.

1 May 2016 in Journal of Atmospheric and Oceanic Technology
Verified
Journal Article
Open access
JRJens Reimann
Jens Reimann
MHMartin Hagen
Martin Hagen
The sun is known to be a good target for weather radar calibration. In this paper high resolution raster scans of the sun at high elevations will be used to derive the antenna pattern of weather radar, without being affected by beam propagation effects and reflections close to the earth surface. It is shown that this pattern matches well to pattern measurements using a point source. Hence, a good estimation of the real antenna pattern can be derived using the sun.Furthermore, formulas to extract undistorted antenna patterns from the sun, even at high elevation angles are derived. The signal processing required to achieve high sensitivity for the antenna pattern measurements will be described. Important parts of the antenna pattern, e.g. side lobes become visible when using long integration times.The polarimetric receiver channel cross-correlation coeffcient is proposed as a figure of merit of the cross-polar isolation of the antenna and hence, the cross-polar pattern. The results are also compared...

27 March 2018 in Remote Sensing
Verified
Journal Article
Open access
PDF file
KSKersten Schmidt
Kersten Schmidt
JRJens Reimann
Jens Reimann
NRNúria Tous Ramon
Núria Tous Ramon
MSMarco Schwerdt
Marco Schwerdt
The geometric accuracy of synthetic aperture radar (SAR) data is usually derived from level-1 products using accurately surveyed corner reflector positions. This paper introduces a novel approach that derives the range delay and azimuth shift from acquired SAR raw data (level-0 products). Therefore, the propagation path is completely retrieved from SAR pulse transmission up to the reception of the point target’s backscatter. The procedure includes simple pulse compression in range and azimuth instead of full SAR data processing. By applying this method, the geometric accuracy of ESA’s Sentinel-1 SAR satellites (Sentinel-1A and Sentinel-1B) is derived for each satellite overpass by using corner reflectors with precisely surveyed GPS positions. The results show that the azimuth bias of about 2 m found in level-1 products for Stripmap acquisitions is reduced to about 15 cm. This indicates an artificial bias arising from operational Sentinel-1 SAR data processing. The remaining range bias of about 1.0 m, observed in L0-products, is interpreted as the offset between the SAR antenna phase center and the spacecraft’s center of gravity. The relative pixel localization accuracy derived with the proposed method is about 12 cm for the evaluated acquisitions. Compared to the full processed level-1 SAR data products, this accuracy is similar in the range direction, but, for the azimuth direction, it is improved by about 50% with the proposed method.

15 May 2018 in Remote Sensing
Verified
Journal Article
Open access
PDF file
MSMarco Schwerdt
Marco Schwerdt
KSKersten Schmidt
Kersten Schmidt
PKPatrick Klenk
Patrick Klenk
NRNúria Tous Ramon
Núria Tous Ramon
DRDaniel Rudolf
Daniel Rudolf
MZManfred Zink
Manfred Zink
The TerraSAR-X mission, based on two satellites, has produced SAR data products of high quality for a number of scientific and commercial applications for more than ten years. To guarantee the stability and the reliability of these highly accurate SAR data products, both systems were first accurately calibrated during their respective commissioning phases and have been permanently monitored since then. Based on a short description of the methods applied, this paper focuses on the radiometric performance including the gain and phase properties of the transmit/receiver modules, the antenna pattern checked by evaluating scenes acquired over uniformly distributed targets and the radiometric stability derived from permanently deployed point targets. The outcome demonstrates the remarkable performance of both systems since their respective launch.

4 December 2013 in Remote Sensing
Verified
Journal Article
Open access
PDF file
BDBjörn Döring
Björn Döring
KSKersten Schmidt
Kersten Schmidt
MJMatthias Jirousek
Matthias Jirousek
DRDaniel Rudolf
Daniel Rudolf
JRJens Reimann
Jens Reimann
MSMarco Schwerdt
Marco Schwerdt
A synthetic aperture radar (SAR) system requires external absolute calibration so that radiometric measurements can be exploited in numerous scientific and commercial applications. Besides estimating a calibration factor, metrological standards also demand the derivation of a respective calibration uncertainty. This uncertainty is currently not systematically determined. Here for the first time it is proposed to use hierarchical modeling and Bayesian statistics as a consistent method for handling and analyzing the hierarchical data typically acquired during external calibration campaigns. Through the use of Markov chain Monte Carlo simulations, a joint posterior probability can be conveniently derived from measurement data despite the necessary grouping of data samples. The applicability of the method is demonstrated through a case study: The radar reflectivity of DLR’s new C-band Kalibri transponder is derived through a series of RADARSAT-2 acquisitions and a comparison with reference point targets (corner reflectors). The systematic derivation of calibration uncertainties is seen as an important step toward traceable radiometric calibration of synthetic aperture radars.

1 June 2020 in Remote Sensing
Verified
Journal Article
Open access
PDF file
JRJens Reimann
Jens Reimann
MSMarco Schwerdt
Marco Schwerdt
Nowadays, stringent requirements for the quality of SAR data products exist. The radiometric and image quality requirements can only be fulfilled by knowing the disturbances caused by the radar hardware itself. The internal calibration is a mechanism to estimate these disturbances from the real hardware. Unfortunately, most of the current internal calibration schemes interrupt the SAR data acquisition during internal calibration and hence cause a loss of azimuth samples and a degradation of the image quality. The calibration is thus often performed only before and after a data take. However, these two calibration events are hardly sufficient to estimate the instrument parameters during the whole acquisition especially for long data takes, which will become more common in future SAR system. In this paper, an internal calibration scheme is introduced which allows performing the internal calibration during nominal data acquisition by injecting a coded calibration signal into the receiver with very low power. This signal causes only minor degradation of the SAR image but can be retrieved from the data using adequate signal processing. This technique is described, the theoretical performance estimated, and finally demonstrated on real data from the TerraSAR-X mission. A selection of possible coding scheme is also analyzed with respect to their suitability for the proposed internal calibration scheme.