Sentinel-1B is the second of two C-Band Synthetic Aperture Radar (SAR) satellites of the Sentinel-1 mission, launched in April 2016—two years after the launch of the first satellite, Sentinel-1A. In addition to the commissioning of Sentinel-1B executed by the European Space Agency (ESA), an independent system calibration was performed by the German Aerospace Center (DLR) on behalf of ESA. Based on an efficient calibration strategy and the different calibration procedures already developed and applied for Sentinel-1A, extensive measurement campaigns were executed by initializing and aligning DLR’s reference targets deployed on the ground. This paper describes the different activities performed by DLR during the Sentinel-1B commissioning phase and presents the results derived from the analysis and the evaluation of a multitude of data takes and measurements.
29 July 2015 in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
In the frame of the COPERNICUS program, the main objective of the Sentinel-1 mission is to ensure the continuity of C-band SAR data for global earth monitoring. Sentinel-1A is the first of two C-band satellites launched in April 2014. In addition to the commissioning of Sentinel-1A executed by the European Space Agency (ESA), an independent verification of the system calibration has been performed by DLR under an ESA contract. For this purpose, the complete calibration chain was developed and established, starting with a calibration concept, a detailed in-orbit calibration plan and the software tools for analyzing and evaluating all the measurements up to the calibration targets serving as accurate reference. Based on an efficient calibration strategy, this paper describes the different activities performed by DLR and presents the results obtained during the commissioning phase (CP) of Sentinel-1A.
Radiometric calibration adjusts the measured pixel intensity to a physical property, the radar cross section (RCS). After calibration, this relationship is defined over the entire backscatter range: from low image power (near noise) up to high reflections (below saturation). Based on a proper radiometric calibration, the measured radar backscatter for the Sentinel-1 synthetic aperture radar (SAR) satellite constellation is validated over a wide backscatter range using different target types. Therefore, the RCS derived from point targets and radar brightness from distributed targets are compared between Sentinel-1A (S-1A) and Sentinel-1B (S-1B) acquisitions over the same observation area for regions where a stable target backscatter is expected for a certain period of time. Low differences (in the order of 0.3 dB) are found between S-1A and S-1B for high and medium backscatter derived from point targets or rainforest regions, but higher differences for low backscattering regions like ice areas and lakes. For comparing radar brightness containing low backscatter targets, an accurate derived noise level has to be taken into account. In addition to the measured lower noise equivalent beta zero (NEBZ) level, higher transmit power was detected for S-1B compared to S-1A. The higher antenna gain of S-1B leads finally to a higher sensitivity for low backscattering areas of S-1B compared to S-1A and explains the found differences.
29 January 2021 in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
The TanDEM-X mission, formed by the TanDEM-X satellite (TDX) in cooperation with its almost identical twin TerraSAR-X (TSX), has mainly been designed to acquire bistatic Synthetic Aperture Radar (SAR) images of the Earth. Initiated in 2010, the primary mission objectives were to generate a global Digital Elevation Model (DEM), to perform scientific measurements and to explore novel SAR techniques. Up to the present day all these objectives have been completed with outstanding results. In addition, the satellites maintained a stable image quality from the start throughout their entire lifetime. The ground segment, which was tailored to the capabilities of the space segment, as well as an excellent design and manufacturing of the satellites were the key elements to achieve such a performance. In addition, the elaborate calibration concept and a careful treatment of the on-board resources enabled full operability up to the present day and allowed additional mission objectives such as the generation of a Change-DEM layer as an update to the global DEM. The stable bus and SAR payload performance as revealed by long-term system monitoring provide the basis for further extension of the TanDEM-X mission for several more years. In the following paper these long-term system monitoring results are presented to provide an overview of the evolution of the radar system. The results and experience gained with more than a decade of TanDEM-X mission operation are a great value for both the scientific and commercial community and serve as a forerunner for the development of future SAR missions.
The geometric accuracy of synthetic aperture radar (SAR) data is usually derived from level-1 products using accurately surveyed corner reflector positions. This paper introduces a novel approach that derives the range delay and azimuth shift from acquired SAR raw data (level-0 products). Therefore, the propagation path is completely retrieved from SAR pulse transmission up to the reception of the point target’s backscatter. The procedure includes simple pulse compression in range and azimuth instead of full SAR data processing. By applying this method, the geometric accuracy of ESA’s Sentinel-1 SAR satellites (Sentinel-1A and Sentinel-1B) is derived for each satellite overpass by using corner reflectors with precisely surveyed GPS positions. The results show that the azimuth bias of about 2 m found in level-1 products for Stripmap acquisitions is reduced to about 15 cm. This indicates an artificial bias arising from operational Sentinel-1 SAR data processing. The remaining range bias of about 1.0 m, observed in L0-products, is interpreted as the offset between the SAR antenna phase center and the spacecraft’s center of gravity. The relative pixel localization accuracy derived with the proposed method is about 12 cm for the evaluated acquisitions. Compared to the full processed level-1 SAR data products, this accuracy is similar in the range direction, but, for the azimuth direction, it is improved by about 50% with the proposed method.
The TerraSAR-X mission, based on two satellites, has produced SAR data products of high quality for a number of scientific and commercial applications for more than ten years. To guarantee the stability and the reliability of these highly accurate SAR data products, both systems were first accurately calibrated during their respective commissioning phases and have been permanently monitored since then. Based on a short description of the methods applied, this paper focuses on the radiometric performance including the gain and phase properties of the transmit/receiver modules, the antenna pattern checked by evaluating scenes acquired over uniformly distributed targets and the radiometric stability derived from permanently deployed point targets. The outcome demonstrates the remarkable performance of both systems since their respective launch.