We propose an isolated high-voltage-gain quasi-resonant dc–dc converter with a bifunctional circuit for the renewable-energy applications. The proposed converter adopts an interleaved connection in the primary side, reducing input-current ripple, and includes the bifunctional circuit operating as the switched-capacitor cells and two active-clamped circuits simultaneously. The converter realizes high-voltage-conversion ratio without using extreme duty ratio, and the voltage spike due to the leakage inductance of the isolation transformer is clamped. In addition, an output voltage doubler in the secondary side comprises a series resonant circuit and then obtains zero-current switching turn- off of rectifying diodes; the diode reverse-recovery problems are also alleviated. A 320 W laboratory prototype that operates at input of 26–34 V and output of 400 V is fabricated to verify the effectiveness of the proposed converter.

This paper presents a high-voltage gain ripple-free resonant DC/DC converter using an active voltage-quadrupler. By incorporating an active voltage-quadrupler at the secondary side of the transformer, the circuit achieved a very high-voltage gain. Without using extra input inductors, the inherent dual transformer plus interleaved active-clamped circuit operating with a fixed duty-ratio of 0.5 generate a ripple-free input current, which extends the lifetime of the fuel cell and shrinks the size of the input capacitive filter. This asymmetric structure of the active-clamp circuit requires an extra dead time for one of the secondary-side switches to achieve zero-voltage switching (ZVS) turn-on. After the extra dead time for one of the secondary-side switches is applied, all power components of the active voltage quadrupler cell are turned on and off with soft switching. The resonant capacitor voltages are unbalanced due to the extra dead time, but they are compensated by applying different secondary-side duty ratios. The operating principle and steady-state characteristics of the proposed converter were analyzed in detail. We built a 1-kW/700-V prototype that copes with 48-72 V inputs, and tested to verify the theoretical analysis.

In this work, a new active balancing circuit is proposed. This circuit consists of a cell-access network and an energy-transfer network. The cell-access network requires 2n + 6 switches, where n is the number of cells, and creates an energy-transfer path between unbalanced cells and the energy-transfer network. The energy-transfer network has double energy carriers and simultaneously implements cell-to-pack and pack-to-cell balancing operations without overlapping. As a result, a high power rate and fast balancing operation can be achieved by using two energy carriers in a single balancing circuit. The prototype of a proposed balancing circuit was built for six cells and then tested under various conditions; all cells in the state of charge (SOC) region of 70% to 80% were equalized after 93 min, and one charging/discharging period in the SOC region of 10% to 90% was increased by 8.58% compared to the non-balancing operation. These results show that the proposed circuit is a good way to balance charges among batteries in a battery pack.

This brief presents a class-C voltage-controlled oscillator (VCO) that ensures a robust start-up with low phase noise and high power efficiency. The proposed start-up scheme, which uses a voltage converter that operates according to the output state, relieves the start-up difficulty by supplying a time-varying bias voltage to the core transistors and allows the VCO to operate in an optimal state. The start-up circuitry is enabled only during initial operation, so power efficiency is improved without phase noise degradation. Furthermore, a capacitor array with a high quality factor is implemented by a direct capacitor connection that exhibits low series resistance. Fabricated with a 65-nm CMOS, the VCO demonstrates a frequency tuning range of 13.1% from 19.3 to 22.0 GHz. The measured minimum phase noise at a 1-MHz offset is −106.33 dBc/Hz at an oscillation frequency of 19.7 GHz, while dissipating 3.8-mW of power from a 1.0-V supply. The VCO occupies an active area of 0.064 mm ² . It reveals a figure-of-merit and figure-of-merit with area of −186.4 and −198.3 dBc/Hz, respectively.

This article proposes a highly efficient quasi-single-stage ac–dc converter that incorporates a bidirectional switch at the secondary side of the circuit. Its attractiveness is that the proposed ac–dc converter achieves almost ZVS turn-off at high instantaneous power and low-voltage turn-off at low instantaneous power. Moreover, the secondary-side switching reduces the loss at the main switch, and thereby more than offsets the losses that occur at the main switch and the clamp switch in a conventional ac–dc converter. An additional benefit of this converter is that the voltages across the primary-side capacitors and secondary-side capacitors are well balanced because the duty cycle at the primary-side switch is fixed at 0.5. Experimental results show that the proposed ac–dc converter is effective and more efficient than a conventional solution.

This paper proposes a bidirectional dc–dc converter for residential micro-grid applications. The proposed converter can operate over an input voltage range that overlaps the output voltage range. This converter uses two snubber capacitors to reduce the switch turn-off losses, a dc-blocking capacitor to reduce the input/output filter size, and a 1:1 transformer to reduce core loss. The windings of the transformer are connected in parallel and in reverse-coupled configuration to suppress magnetic flux swing in the core. Zero-voltage turn-on of the switch is achieved by operating the converter in discontinuous conduction mode. The experimental converter was designed to operate at a switching frequency of 40–210 kHz, an input voltage of 48 V, an output voltage of 36–60 V, and an output power of 50–500 W. The power conversion efficiency for boost conversion to 60 V was ≥98.3% in the entire power range. The efficiency for buck conversion to 36 V was ≥98.4% in the entire power range. The output voltage ripple at full load was <3.59 V_p.p for boost conversion (60 V) and 1.35 V_p.p for buck conversion (36 V) with the reduced input/output filter. The experimental results indicate that the proposed converter is well-suited to smart-grid energy storage systems that require high efficiency, small size, and overlapping input and output voltage ranges.