Jamil Hassan

Jamil Hassan

Auto-generated profile, based on publicly available information

Jamil Hassan

Division of Electronics and Electrical Engineering, Dongguk University-Seoul, Seoul, South Korea

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 May 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JLJong-Won Lim
Jong-Won Lim
JHJamil Hassan
Jamil Hassan
MKMinsung Kim
Minsung Kim
This article presents a bidirectional soft-switching push-pull resonant converter that is highly efficient over a wide range of battery voltages. It is derived by integrating a current-fed push-pull circuit and an active voltage doubler circuit with a bidirectional switch. The converter operates as a pulsewidth modulation (PWM) current-fed push-pull resonant-boost converter in the forward direction, but as a PWM half-bridge resonant converter in the backward direction. The most attractive feature of the proposed converter is that, by employing the bidirectional switch and corresponding switching modulation, it can achieve almost ZVS at turn-off instants under wide variations of battery voltages. Therefore, the proposed converter achieves high efficiency even during high-frequency operation. Moreover, no instantaneous reactive current flows through the circuit under wide variations of battery voltages and loads. Furthermore, the proposed bidirectional resonant converter has a high conversion ratio in both power flow directions without using a transformer that has high turns-ratio. The operating principles and characteristics of the proposed bidirectional resonant converter are presented in detail. Experimental results using a 1-kW prototype verified the feasibility and efficiency of the proposed converter.

3 September 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JHJamil Hassan
Jamil Hassan
CBChangkyu Bai
Changkyu Bai
HSHwasoo Seok
Hwasoo Seok
JLJong-Won Lim
Jong-Won Lim
SASuk-Ho Ahn
Suk-Ho Ahn
MKMinsung Kim
Minsung Kim
This article proposes a highly efficient current-fed half-bridge resonant converter over a wide range of the output voltages. By adding a bidirectional switch across center nodes of the voltage doubler and applying corresponding switching modulation, the converter accomplishes almost zero-voltage switching at the turn- off instant under the wide output voltage variations. Moreover, the circuit experiences very little instantaneous reactive current even when the output voltage varies widely. Primary-side duty cycle fixed at 0.5 balances the voltages across the capacitors at the primary side and at the secondary side each irrespective of the output voltage variation; it also limits the voltage stress at the active power components. Therefore, the proposed converter delivers high efficiency and compact component size. We fabricated a 400-W experimental prototype to validate the superior properties of the proposed converter.

27 October 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
JHJamil Hassan
Jamil Hassan
CBChangkyu Bai
Changkyu Bai
JLJong-Won Lim
Jong-Won Lim
MKMinsung Kim
Minsung Kim
This article proposes a high step-up quasi-resonant converter that minimizes switching loss over a wide range of input voltages. By employing a bidirectional switch and corresponding switching modulation, the proposed converter achieves the main switch with almost zero voltage, and therefore incurs very little switching loss at all active switches. Moreover, no instantaneous reactive current flows through the circuit under wide variations of input voltages and loads. The duty cycle of primary-side switches is fixed to 0.5; then, the input and clamp capacitor voltages become identical, and thereby the following resonant capacitor voltages remain in balance. As a consequence, the proposed converter becomes compact and achieves high boost-ratio and high efficiency over a wide range of input voltages. The operating principle of the converter is presented along with its design procedure. 400-W/380-V prototype of the proposed converter has been implemented and tested at 40-60 V to verify its effectiveness.

28 January 2022 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
JHJamil Hassan
Jamil Hassan
JLJong-Won Lim
Jong-Won Lim
TWTsegaab Alemayehu Wagaye
Tsegaab Alemayehu Wagaye
Byeongcheol HanByeongcheol Han
Byeongcheol Han
SLSang-Won LEEee
Sang-Won LEEee
MKMinsung Kim
Minsung Kim
This article proposes a highly efficient quasi-single-stage ac–dc converter that incorporates a bidirectional switch at the secondary side of the circuit. Its attractiveness is that the proposed ac–dc converter achieves almost ZVS turn-off at high instantaneous power and low-voltage turn-off at low instantaneous power. Moreover, the secondary-side switching reduces the loss at the main switch, and thereby more than offsets the losses that occur at the main switch and the clamp switch in a conventional ac–dc converter. An additional benefit of this converter is that the voltages across the primary-side capacitors and secondary-side capacitors are well balanced because the duty cycle at the primary-side switch is fixed at 0.5. Experimental results show that the proposed ac–dc converter is effective and more efficient than a conventional solution.

1 July 2026 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JHJamil Hassan
Jamil Hassan
APAswin Palanisamy
Aswin Palanisamy
MKMinsung Kim
Minsung Kim
DLDylan Lu
Dylan Lu
Yam SiwakotiYam Siwakoti
Yam Siwakoti
This article proposes a novel Symmetric Unipolar Modulation (SUM) strategy for Dual Active Bridge (DAB) converters, which significantly enhances power density by improving transformer utilization factor and reducing the size of passive components. The proposed SUM technique effectively doubles the transformer frequency ($f_{\text{TX}}$) to $2f_{sw}$ while maintaining the switching frequency ($f_{sw}$) of both the primary and secondary side bridge switches at $f_{sw}$, unlike conventional methods where the semiconductor and transformer frequencies are equal. By pushing the transformer frequency to a higher level, the proposed technique minimizes passive component dimensions without introducing additional stress on the active or passive components. Moreover, the SUM approach reshapes the transformer core flux density from triangular to trapezoidal while reducing its peak and enabling further reduction in magnetic core size. It also reduces the voltage stress across the transformer by half compared to conventional modulation strategies, thereby improving the overall performance of the converter. Experimental validation using a 1-kW prototype confirms the effectiveness of the proposed modulation technique in achieving these benefits.